Peugeot 508Updated 10 min read

Peugeot 508 I Gauges and Service Indicator

How to read the gauges and service indicator on your Peugeot 508 I, reset the service spanner, and understand oil level and AdBlue range warnings.

Peugeot 508 (2014-present) on a coastal road at dusk with its headlamps on
Image adapted from a photo by Sleeptsov, CC BY-SA 4.0.

Hello and welcome. In this post, we'll look at the gauges and the service indicator on the Peugeot 508 I (2014-present). The gauges and service indicator on your Peugeot 508 tell you when the next service is due, whether the engine coolant and oil temperatures are correct, and how much range you have left before AdBlue or an emissions fault stops the engine from starting. We'll cover what each display means and what you should do. Some displays, such as the electric oil level indicator and the AdBlue range indicators, depend on the version or equipment, so you may not see all of them on your 508.

How do I reset the service light on my Peugeot 508?

Switch off the ignition, press and hold the trip distance recorder reset button, then switch the ignition back on. Release the button when the display shows =0 and the spanner disappears.

Peugeot 508 I service-indicator reset: hold the trip-distance reset button, switch the ignition on, and release when the display shows =0

Quick Reference

Scroll the table sideways.

SectionIn short
Service indicatorService due alerts, resetting and checking service information
Engine coolant temperature gaugeCoolant temperature zones and how to top up safely
Engine oil level indicatorOil temperature zones and electric oil level messages
AdBlue fluid range indicatorsAdBlue and SCR fault range before starting is prevented

Service indicator

The service indicator shows the service spanner and the distance left before your next service. It appears for a few seconds on the instrument panel when you switch on the ignition.

Service-indicator key or spanner symbol on the instrument panel, with the remaining distance or time

Scroll the table sideways.

Service spannerWhat it meansWhat you see
On for a few seconds when the ignition is switched onThere are between 620 miles (1,000 km) and 1,860 miles (3,000 km) before the next service is due.Depending on version, the distance recorder shows the distance remaining, or an alert shows the distance and the period remaining. The spanner goes off after a few seconds.
Stays on when the ignition is switched onLess than 620 miles (1,000 km) remain before the next service is due.Depending on version, the distance recorder shows the distance remaining, or an alert message shows the distance and the period remaining. The spanner stays on because the service is needed very soon.
Flashes then stays on when the ignition is switched onThe servicing interval has been exceeded.Depending on version, the total distance recorder shows the distance travelled since the due date, preceded by a "-" sign, or an alert message tells you the due date has passed. The spanner stays on until the service has been done.
Flashes then stays on, together with the Service warning lampThe servicing interval has been exceeded on Diesel BlueHDi versions.As above. The spanner stays on until the service has been done.

The alert may come on close to the due date, and it is triggered once the due date has passed. The distance shown is calculated from the mileage covered and the time elapsed since the last service.

After each service, the service indicator must be reset to zero. If you have serviced your car yourself:

  1. Ignition off: Switch off the ignition.
  2. Hold the button: Press and hold the trip distance recorder reset button.
  3. Ignition on: Switch on the ignition. The distance recorder display starts a countdown.
  4. Release: When the display shows "=0", release the button. The spanner disappears.

If you need to disconnect the battery after resetting, lock the car and wait at least five minutes so the reset is registered.

You can check the service information at any time: press the trip distance recorder reset button and the information is displayed for a few seconds, then disappears.

Engine coolant temperature gauge

With the engine running, the coolant temperature gauge shows whether the engine is at the right temperature.

  • Zone A: the temperature is correct.
  • Zone B: the temperature is too high. The central STOP warning lamp comes on, with an audible signal and a message on the instrument panel screen.

If the needle is in zone B:

  1. Stop: Stop as soon as it is safe to do so.
  2. Wait: Wait a few minutes before switching off the engine.
  3. Get help: Contact a PEUGEOT dealer or a qualified workshop.

After a few minutes of driving, the temperature and pressure in the cooling system rise. To top up the coolant:

  1. Let it cool: Wait for the engine to cool down.
  2. Release the pressure: Unscrew the cap by two turns so the pressure can drop.
  3. Remove the cap: Once the pressure has dropped, take the cap off.
  4. Top up: Fill up to the "MAX" mark.

Take care, as you can be burned when topping up the cooling system. Never fill above the maximum level shown on the reservoir.

Engine oil level indicator

When you switch on the ignition or while you are driving, this gauge shows the engine oil temperature.

  • Zone C: the temperature is correct.
  • Zone D: the temperature is too high. Slow down to lower the oil temperature.

On versions with an electric oil level indicator, the oil level is shown on the instrument panel for a few seconds after the servicing information. The reading is only correct if the car is on level ground and the engine has been off for more than 30 minutes.

Oil level insufficient: the message "Oil level incorrect" appears on the instrument panel, with the Service warning lamp and an audible signal. If a check with the dipstick confirms the level is low, you must top it up to avoid damaging the engine.

Oil level indicator fault: the message "Oil level measurement invalid" appears on the instrument panel. The oil level is then no longer monitored, so you must check it with the manual dipstick under the bonnet. Contact a PEUGEOT dealer or a qualified workshop.

For more on checking levels, see the corresponding section below.

AdBlue fluid range indicators

When the AdBlue® tank is on reserve, or after a fault with the SCR emissions control system has been detected, an indicator shows an estimate of the distance you can cover before the engine is prevented from starting. If there is a system fault and a low AdBlue® level at the same time, the shorter range is shown.

Once the AdBlue® tank is empty, the starting prevention system required by regulations switches on automatically.

Scroll the table sideways.

Remaining rangeWhat you seeWhile driving
Greater than 1,500 miles (2,400 km)No automatic display when you switch on the ignition. Pressing the button shown temporarily displays the remaining range. Above approximately 3,000 miles (5,000 km), the value is not specified.No message
Between 1500 and 375 miles (2400 and 600 km)The UREA warning lamp comes on, with an audible signal and a message such as "Top up emissions additive: Starting prevented in 900 miles".Message shown approximately every 200 miles (300 km) until you top up
Below 375 miles (600 km)The SERVICE warning lamp comes on and the UREA warning lamp flashes, with an audible signal and a message such as "Top up emissions additive: Starting prevented in 350 miles".Message shown every 30 seconds until you top up
Tank emptyThe SERVICE warning lamp comes on and the UREA warning lamp flashes, with an audible signal and the message "Top-up emissions additive: Starting prevented".The engine cannot be started

When the range is low, go to a PEUGEOT dealer or a qualified workshop to have the AdBlue® topped up, or top up the tank yourself. Otherwise you will not be able to restart the car. If the tank is empty, recommends calling on a PEUGEOT dealer or a qualified workshop for the top-up. If you do it yourself, you must add at least 4 litres of AdBlue®.

If a fault with the SCR emissions control system is confirmed, a system that prevents engine starting switches on automatically from 650 miles (1,100 km) after confirmation. Have the system checked by a PEUGEOT dealer or a qualified workshop as soon as possible.

  • Fault detected: the UREA, SERVICE and engine diagnostic warning lamps come on, with an audible signal and the message "Emissions fault". The alert appears while driving when the fault is first detected, then each time you switch on the ignition while the fault persists. If the fault is temporary, the alert disappears during the next journey after the SCR system has run its self-diagnosis.
  • Authorised driving phase (between 658 and 0 miles (1 100 km and 0 km)): the fault is confirmed after 30 miles (50 km) with the fault message permanently displayed. The SERVICE and engine diagnostic warning lamps come on and the UREA warning lamp flashes, with an audible signal and a message such as "Emissions fault: Starting prevented in 200 miles (300 km)". While driving, the message appears every 30 seconds while the fault persists, and the alert repeats when you switch on the ignition. Go to a PEUGEOT dealer or a qualified workshop as soon as possible, or you will not be able to restart the car.
  • Starting prevented: each time you switch on the ignition, the SERVICE and engine diagnostic warning lamps come on and the UREA warning lamp flashes, with an audible signal and the message "Emissions fault: Starting prevented". You have gone past the authorised driving limit, so you must call on a PEUGEOT dealer or a qualified workshop to start the engine.

For more on AdBlue®, the SCR system and topping up, see the corresponding section below.

Frequently Asked Questions

How do I reset the service light on my Peugeot 508?

Switch off the ignition, press and hold the trip distance recorder reset button, then switch the ignition back on. Release the button when the display shows "=0" and the spanner disappears.

Why is the spanner flashing on my Peugeot 508 dashboard?

If the service spanner flashes and then stays on when you switch on the ignition, the servicing interval has been exceeded. It stays on until the service has been done.

What does "Oil level measurement invalid" mean on a Peugeot 508?

It means the electric oil level indicator has a fault and the oil level is no longer monitored. Check the level with the dipstick under the bonnet and contact a PEUGEOT dealer or a qualified workshop.

How much AdBlue do I need to add if my Peugeot 508 won't start?

If the AdBlue® tank is empty and you top it up yourself, you must add at least 4 litres of AdBlue®. recommends calling on a PEUGEOT dealer or a qualified workshop for this top-up.

Your 508's gauges and service indicator give you plenty of warning before a problem becomes serious, from a service falling due to AdBlue running low. Keep an eye on them when you switch on the ignition, and ask a PEUGEOT dealer or a qualified workshop for full details on any system.

More Peugeot 508 Guides

To find out what the other lamps on your dashboard mean, read our guides to the Peugeot 508 red warning lights, Peugeot 508 orange warning lights and Peugeot 508 green and blue indicator lamps.

Don't forget to follow us on Instagram for more Peugeot guides!

This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.

Related guides: Peugeot 508 model guides.

Cover adapted from a photograph by Sleeptsov — Wikimedia Commons, CC BY-SA 4.0 (AI edited).

Related guides

Guide ·

Peugeot 508 II 12V Battery and Jump Starting

Hello and welcome. This article covers the 12 V battery on the Peugeot 508 II (2018-2023): reaching it, jump starting, charging with a charger, and disconnecting and reconnecting it. We also look at t

Guide ·

Peugeot 508 II Tyre Pressure

Hello and welcome. This article looks at the under-inflation detection system on the Peugeot 508 II (2018-2023). We cover what the alert means, reinitialising the system after adjusting pressures, and

Guide ·

Peugeot 508 I 12V Battery and Jump Starting

Hello and welcome. In this post we look at the 12 V battery on the Peugeot 508 I (2014-present). We cover jump starting from another battery, charging with a charger, disconnecting and reconnecting, a