Peugeot 508 II 12V Battery and Jump Starting
Hello and welcome. This article covers the 12 V battery on the Peugeot 508 II (2018-2023): reaching it, jump starting, charging with a charger, and disconnecting and reconnecting it. We also look at t
How to use the temporary puncture repair kit, change a wheel and use the spare wheel on your Peugeot 508 I. Covers the Peugeot 508 I (2014-present).

Hello and welcome. In this post, we'll look at the temporary puncture repair kit and the spare wheel on the Peugeot 508 I (2014-present). A flat tyre is never welcome, but your Peugeot 508 gives you the tools to deal with it. Depending on the car, you have a temporary puncture repair kit, a spare wheel with tools, or both. This guide explains how to use the repair kit, how to check tyre pressures with its compressor, and how to change a wheel safely. Some items depend on the version, the equipment fitted or the country of sale, so your 508 may not have everything described here.
The kit is in the under-floor storage, under the boot floor.
Scroll the table sideways.
| Section | In short |
|---|---|
| Temporary puncture repair kit | What the repair kit does and when to use it |
| Access to the kit | Where the kit is, its tools and parts |
| Repair procedure | Seal the puncture, reinflate, then replace the cartridge |
| Checking / adjusting tyre pressures | Using the compressor without sealant to inflate |
| Access to the tools | Where the wheel-changing tools are and what they do |
| Access to the spare wheel | Taking out and stowing the spare wheel |
| Removing a wheel | Park safely, jack up and remove the wheel |
| Fitting a wheel | Refit the wheel, tighten bolts and get checked |
The temporary puncture repair kit is made up of a compressor and a sealant cartridge. It lets you repair a tyre temporarily so that you can get to the nearest garage.

The kit is stored in the under floor storage, under the boot floor. The tools are specific to your car and may vary according to the level of equipment, so do not use them for any other purpose.
Only the 12 V sockets at the rear of the car and in the boot can power the compressor. The 12 V sockets at the front and in the centre console armrest are not suitable.
Scroll the table sideways.
| Letter | Part |
|---|---|
| A | "Sealant" or "Air" position selector |
| B | On "I" / off "O" switch |
| C | Deflation button |
| D | Pressure gauge (in bars and psi) |
| E | Compartment with a cable and adaptor for the 12 V socket, and various inflation adaptors for accessories such as balls and bicycle tyres |
| F | Sealant cartridge |
| G | White pipe with cap for repair |
| H | Black pipe for inflation |
| I | Speed limit sticker |
Stick the speed limit sticker I on the steering wheel to remind you that a wheel is in temporary use. Do not exceed 50 mph (80 km/h) with a tyre repaired using this kit. If your car has tyre under-inflation detection, the under-inflation warning lamp will stay on after the repair until a PEUGEOT dealer or a qualified workshop reinitialises the system.
The repair has two stages: first you inject the sealant, then you check and adjust the pressure.
Stage 1: Sealant
Do not try to remove any foreign object stuck in the tyre. Never start the compressor before the white pipe is connected to the valve, or the sealant will be pushed out through the pipe. The sealant is harmful if swallowed and irritates the eyes, so keep it out of the reach of children. If the pressure has not reached 2 bars after around 5 to 7 minutes, the tyre cannot be repaired: contact a PEUGEOT dealer or a qualified workshop.
Stage 2: Air
A significant loss of pressure means the puncture has not been fully plugged, so contact a PEUGEOT dealer or a qualified workshop. Either way, go to a PEUGEOT dealer or a qualified workshop as soon as possible and tell the technician you have used this kit. After inspection, they will tell you whether the tyre can be repaired or must be replaced.
Removing the cartridge
Watch out for fluid escaping. The expiry date of the fluid is printed on the cartridge. The cartridge is single use, so replace it even if it is only partly used. Do not throw it away in the environment: take it to an authorised waste disposal site or a PEUGEOT dealer. Remember to get a new cartridge from a PEUGEOT dealer or a qualified workshop.
You can use the compressor without injecting any sealant to:
If your car has a spare wheel, the tools for changing a wheel are stored in the boot under the floor.
The tools are specific to your car and can vary according to the level of equipment. Do not use them for any other purpose.
Only use the jack to change a wheel with a damaged or punctured tyre. The jack needs no maintenance and meets the European standards defined in the Machinery Directive 2006/42/EC. If your wheel has a hub cap, refit it with its notch facing the valve, then press around its edge with the palm of your hand.
The spare wheel is in the boot under the floor. Depending on the country of sale, it may be steel, alloy or a "space-saver" type. Depending on equipment, it is held by a strap or by a securing nut A and bolt B. The steps below are for the nut and bolt.

Taking out the wheel
Putting the wheel back
The space-saver and steel spare wheels have no tyre under-inflation sensor. Have the punctured wheel repaired by a PEUGEOT dealer or a qualified workshop.
Before you start, make sure the car is parked safely.
All passengers must get out and wait somewhere safe. Only use the jack supplied by the manufacturer, and only for lifting the car. Never go under a car raised on a jack: use an axle stand. If your car has no jack, ask a PEUGEOT dealer or a qualified workshop for the part numbers of the jack and wheelbrace.
Make sure the jack is stable: on slippery or loose ground it can slip or collapse, with a risk of injury. Only use jacking points A or B, centred on the jack head, or the car could be damaged and the jack could collapse.
Follow these steps to fit the spare wheel.
With alloy wheels, it is normal for the bolt washers not to touch a space-saver spare wheel: the wheel is held by the conical contact of each bolt. Do not exceed 50 mph (80 km/h) on a space-saver spare. To store the punctured wheel in the boot, remove its central cover first. Have the bolt tightness and spare wheel pressure checked by a PEUGEOT dealer or a qualified workshop without delay, and have the punctured wheel repaired and refitted as soon as possible.
The kit is in the under floor storage, under the boot floor.
Do not exceed 50 mph (80 km/h) and limit the distance to approximately 120 miles (200 km). Go to a PEUGEOT dealer or a qualified workshop as soon as possible.
If your 508 has tyre under-inflation detection, the warning lamp stays on after the repair until a PEUGEOT dealer or a qualified workshop reinitialises the system.
No. The cartridge is single use and must be replaced even if it is only partly used, so get a new one from a PEUGEOT dealer or a qualified workshop.
Whether you use the repair kit or the spare wheel, take your time, work somewhere safe and follow the steps in order. Afterwards, have your Peugeot 508 checked by a PEUGEOT dealer or a qualified workshop, and keep in the car for full details.
To understand what the lamps on your dashboard mean, see our guides to the Peugeot 508 red warning lights, the Peugeot 508 orange warning lights and the Peugeot 508 green and blue indicator lamps.
Don't forget to follow us on Instagram for more Peugeot guides!
This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.
Related guides: Peugeot 508 model guides.
Cover adapted from a photograph by Sleeptsov — Wikimedia Commons, CC BY-SA 4.0 (AI edited).
Hello and welcome. This article covers the 12 V battery on the Peugeot 508 II (2018-2023): reaching it, jump starting, charging with a charger, and disconnecting and reconnecting it. We also look at t
Hello and welcome. This article looks at the under-inflation detection system on the Peugeot 508 II (2018-2023). We cover what the alert means, reinitialising the system after adjusting pressures, and
Hello and welcome. In this post we look at the 12 V battery on the Peugeot 508 I (2014-present). We cover jump starting from another battery, charging with a charger, disconnecting and reconnecting, a