Peugeot 508Updated 7 min read

Peugeot 508 I Headlight Bulbs and Replacement

How to change a Peugeot 508 I headlight, fog or number-plate bulb, why you must not touch halogen glass, and why LED units are not a DIY job.

Peugeot 508 (2014-present) parked at night with its headlamps and rear lamps on
Image adapted from a photo by Sleeptsov, CC BY-SA 4.0.

Hello and welcome. In this post, we'll look at which bulbs are used and how to replace a headlight bulb on the Peugeot 508 I (2014-present). It also tells you which lamps use LEDs, because those must be replaced by a PEUGEOT dealer or a qualified workshop. The lamps fitted depend on the version and equipment of your car, for example full LED or halogen headlamps, Saloon, SW or RXH, so not every item here will apply to your 508.

How do I change a headlight bulb on a Peugeot 508?

Open the bonnet, remove the cover at the back of the lamp, then turn or unclip the holder for that bulb type. Do not touch the glass of a new halogen bulb; fingerprints can damage it. LED units are not a DIY replacement — leave those to a PEUGEOT dealer or a qualified workshop.

A 508 I headlight bulb is reached from under the bonnet by removing the cover at the back of the lamp.
Do not touch the glass of a new halogen bulb. LED headlamp or daytime-running units are not a DIY replacement.

Quick Reference

Scroll the table sideways.

SectionIn short
Changing a bulbSafety rules, lens care and LED versus halogen bulbs
Front lampsFront lamp layout and halogen headlamp bulb changing
Rear lamps (Saloon)Saloon rear bulb types, indicator and reversing lamp steps
Rear lamps (SW and non-hybrid RXH)SW and RXH rear bulbs, number plate and third brake lamp

Changing a bulb

Before you change any bulb, read these safety points.

  • Burn risk: only change a bulb with the ignition off and after the headlamp has been switched off for several minutes. The bulb can cause serious burns.
  • Handling: do not touch the bulb directly with your fingers. Use a lint-free cloth.
  • Bulb type: only use anti-ultraviolet (UV) type bulbs, so you do not damage the headlamp.
  • Replacement: always replace a failed bulb with a new one of the same type and specification.
  • LED lamps: contact a PEUGEOT dealer or a qualified workshop to replace any light-emitting diode (LED).
  • Halogen bulbs: check that the bulb is correctly positioned in its housing, so the lighting works properly.

The headlamps have polycarbonate lenses with a protective coating, so clean them with care:

  • Do not use a dry or abrasive cloth, a detergent or a solvent product.
  • Use a sponge and soapy water or a pH neutral product.
  • If you use a high pressure washer on stubborn marks, do not keep the lance pointed at the lamps or their edges for too long. This can damage the protective coating and seals.

In some weather, such as low temperature or humidity, misting on the inside of the headlamp and rear lamp glass is normal. It clears after the lamps have been on for a few minutes.

Front lamps

The front lamps depend on whether your 508 has full LED or halogen headlamps.

On models with full LED headlamps, the additional lighting, dipped beam, main beam, daytime running lamps, direction indicators / sidelamps and front foglamps all use LEDs.

On models with halogen headlamps:

Scroll the table sideways.

LampType
Dipped beam headlampsH7
Main beam headlampsH7
Daytime running lampsLED
Direction indicators / SidelampsLED
FoglampsLED

On the non-hybrid RXH model, the lower part holds the daytime running lamps / sidelamps and the direction indicators, all LEDs.

You reach the bulbs by opening the bonnet. The engine may be warm, so take care to avoid burns. Keep objects and clothing away from the engine fan blades, as they could get caught and cause strangulation.

To change a dipped beam or main beam bulb on the halogen model:

  1. Cover: remove the protective plastic cover by pulling the tab.
  2. Bulb holder: unclip the bulb holder.
  3. Bulb: pull the bulb out and fit the new one.
  4. Refit: put everything back in reverse order.

For the left-hand dipped beam headlamp, you need to remove the battery first. see the battery section below.

The door mirror spotlamps use an LED, and the integrated direction indicator side repeaters must also be replaced by a PEUGEOT dealer or a qualified workshop.

Rear lamps (Saloon)

On the Saloon, you can change the direction indicator and reversing lamp bulbs yourself. The other rear lamps use LEDs.

Scroll the table sideways.

LampType
Brake lampsLED
SidelampsLED
Direction indicatorsPY21W amber
Foglamps / Reversing lampsLED / W16W

To change a direction indicator bulb:

  1. Access: open the boot, then the plastic cover.
  2. Nuts: remove the two lamp unit fixing nuts.
  3. Lamp unit: carefully pull the lamp unit out from the outside.
  4. Connector: disconnect the lamp connector.
  5. Bulb holder: spread the tabs and remove the bulb holder.
  6. Bulb: turn the bulb a quarter of a turn and fit the new one.
  7. Refit: put everything back in reverse order.

To change a reversing lamp bulb:

  1. Bulb holder: remove the direction indicator bulb holder as described above.
  2. Bulb: turn the bulb a quarter of a turn and fit the new one.
  3. Refit: put everything back in reverse order.

Rear lamps (SW and non-hybrid RXH)

On the SW and non-hybrid RXH, the direction indicators sit on the wings and the reversing lamps on the tailgate.

Scroll the table sideways.

LampType
Brake lampsLED
Reversing lampsW19W
Direction indicatorsPY21W amber
SidelampsLED
FoglampsLED

To change a direction indicator bulb on the wing:

  1. Access: open the boot, then remove the access cover.
  2. Foam: remove the sealing foam.
  3. Connector: disconnect the lamp connector.
  4. Nut: remove the lamp fixing nut.
  5. Lamp unit: carefully pull the lamp unit out from the outside.
  6. Foam: remove the sealing foam.
  7. Bulb holder: unclip the bulb holder.
  8. Bulb: turn the bulb a quarter of a turn and fit the new one.
  9. Refit: put everything back in reverse order.

To change a reversing lamp bulb on the tailgate:

  1. Access: open the tailgate, then remove the access cover.
  2. Connector: disconnect the lamps connector.
  3. Nut: remove the lamp fixing nut.
  4. Lamp unit: carefully pull the lamp unit out from the outside.
  5. Foam: remove the sealing foam.
  6. Bulb: turn the bulb holder a quarter of a turn and fit the new bulb.
  7. Refit: put everything back in reverse order.

To change a number plate lamp bulb:

  1. Screwdriver: insert a thin screwdriver into one of the outer holes of the lens.
  2. Unclip: push the screwdriver outwards to unclip the lamp.
  3. Connector: disconnect the lamp connector.
  4. Lens: remove the lens.
  5. Bulb: pull the bulb out and fit the new one.

The third brake lamp uses LEDs, so contact a PEUGEOT dealer or a qualified workshop to replace it.

Frequently Asked Questions

What bulb do Peugeot 508 halogen headlamps use?

On models with halogen headlamps, both the dipped beam and main beam headlamps use H7 bulbs. Always use anti-UV type bulbs of the same type and specification.

Do I need to remove the battery to change the left headlamp bulb on a Peugeot 508?

Yes. On the halogen model, you need to remove the battery to change the left-hand dipped beam headlamp bulb.

What bulb is used in the Peugeot 508 rear indicators?

The rear direction indicators use PY21W amber bulbs on both the Saloon and the SW and non-hybrid RXH. The reversing lamps use W16W on the Saloon and W19W on the SW and non-hybrid RXH.

Can I replace the LED lamps on my Peugeot 508 myself?

No. Contact a PEUGEOT dealer or a qualified workshop to replace any LED lamp, including the full LED headlamps and the third brake lamp.

Most of the bulbs you can change on your Peugeot 508 are at the rear, plus the H7 headlamp bulbs on halogen models. Let the lamps cool first, use the correct bulb type, and leave any LED lamp to a PEUGEOT dealer or a qualified workshop.

More Peugeot 508 Guides

If a lamp fault shows on your dashboard, see our guides to the Peugeot 508 red warning lights, Peugeot 508 orange warning lights and Peugeot 508 green and blue indicator lamps.

Don't forget to follow us on Instagram for more Peugeot guides!

This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.

Related guides: Peugeot 508 model guides; Peugeot 508 i 2014 current 12v battery and jump starting.

Cover adapted from a photograph by Sleeptsov — Wikimedia Commons, CC BY-SA 4.0 (AI edited).

Related guides

Guide ·

Peugeot 508 II 12V Battery and Jump Starting

Hello and welcome. This article covers the 12 V battery on the Peugeot 508 II (2018-2023): reaching it, jump starting, charging with a charger, and disconnecting and reconnecting it. We also look at t

Guide ·

Peugeot 508 II Tyre Pressure

Hello and welcome. This article looks at the under-inflation detection system on the Peugeot 508 II (2018-2023). We cover what the alert means, reinitialising the system after adjusting pressures, and

Guide ·

Peugeot 508 I 12V Battery and Jump Starting

Hello and welcome. In this post we look at the 12 V battery on the Peugeot 508 I (2014-present). We cover jump starting from another battery, charging with a charger, disconnecting and reconnecting, a