Peugeot 2008Updated 9 min read

Peugeot 2008 I Battery Location and Jump Starting

How to reach, jump start, charge and disconnect the 12 V battery on your Peugeot 2008 I,. Covers the Peugeot 2008 I (2016-present).

Peugeot 2008 (2016-present) with the bonnet up on a frosty winter morning
Image adapted from a photo by Vauxford, CC BY-SA 4.0.

Hello and welcome. In this post, we'll look at where the 12 V battery is, and how to jump start or charge it on the Peugeot 2008 I (2016-present). A flat 12 V battery can leave you stuck, so it helps to know how to deal with it safely. This guide explains where the battery is on your Peugeot 2008, how to start the engine using another battery, how to charge the battery with a charger and how to disconnect and reconnect it if the car is laid up for a long time. Some details, such as the plastic cover on the (+) terminal or the Stop & Start battery, depend on the version or equipment fitted to your car.

Where is the 12 V battery on a Peugeot 2008 I?

It sits under the bonnet. Use the remote earth point on the engine mounting rather than the battery negative terminal when you jump start.

Quick Reference

Scroll the table sideways.

SectionIn short
General pointsBattery safety, disposal and Stop & Start notes
Access to the batteryBattery is under the bonnet, earth point on engine mounting
Starting using another batteryJump start order, safety checks and charging time afterwards
Charging the battery using a battery chargerWhen and how to charge with a 12 V charger
Disconnecting the batteryDisconnect the (+) clamp and reset settings afterwards

General points

This section covers starting the engine using another battery and charging a discharged battery. Your 2008 has a lead-acid starter battery.

Disposal:

  • Batteries contain harmful substances such as sulphuric acid and lead.
  • They must be disposed of in line with regulations and must never be thrown away with household waste.
  • Take used remote control batteries and vehicle batteries to a special collection point.

Safety when handling the battery:

  • Protect your eyes and face before you handle the battery.
  • Always work in a well ventilated area, away from naked flames and anything that could cause sparks, to avoid the risk of explosion or fire.
  • Wash your hands afterwards.
  • Versions with Stop & Start have a 12 V lead-acid battery of a specific technology and specification. Only a PEUGEOT dealer or a qualified workshop should replace it.
  • If your car has an electronic or automatic gearbox, never try to start the engine by pushing the car.

Stop & Start may not work during the journey after the first engine start. It only becomes available again once the car has been parked continuously for a period that depends on the outside temperature and the battery's state of charge (up to about 8 hours).

Access to the battery

The battery is under the bonnet.

Peugeot 2008 I 12 V battery under the bonnet, with the remote earth point on the engine mounting
  1. Open the bonnet: pull the interior release lever, then release the exterior safety catch.
  2. Secure the bonnet: fit the bonnet stay.
  3. Uncover the terminal: lift the plastic cover on the (+) terminal.

You cannot reach the battery's (-) terminal. Use the remote earth point instead, which is on the right side of the engine mounting.

Starting using another battery

If your battery is flat, you can start the engine using a backup battery (a separate one or one from another vehicle) with jump leads, or with a battery booster.

Peugeot 2008 I jump-starting: red lead to the (+) terminal, black lead to the remote earth point

Before you start:

  • Never try to start the engine by connecting a battery charger.
  • Never use a battery booster of 24 V or higher.
  • Check that the backup battery has a nominal voltage of 12 V and a capacity at least equal to that of your flat battery.
  • Make sure the two vehicles are not touching each other.
  • Switch off all electrical consumers on both vehicles (audio system, wipers, lighting, etc.).
  • Keep the jump leads away from moving parts of the engine (fan, belts, etc.).
  • Do not disconnect the (+) terminal while the engine is running.
  1. Uncover the terminal: lift the plastic cover on the (+) terminal, if your car has one.
  2. Red cable, flat battery: connect the red cable to the (+) terminal of flat battery A, at the metal elbow.
  3. Red cable, backup battery: connect the other end of the red cable to the (+) terminal of backup battery B or the booster.
  4. Green or black cable, backup battery: connect one end to the (-) terminal of backup battery B or the booster, or to an earth point on the other vehicle.
  5. Green or black cable, your car: connect the other end to earth point C on your car.
  6. Start the helper vehicle: start the engine of the vehicle with the good battery and leave it running for a few minutes.
  7. Start your car: operate the starter and let the engine turn. If it does not start straight away, switch off the ignition and wait a few moments before trying again.
  8. Wait for idle: let the engine return to idle.
  9. Remove the leads: disconnect the jump leads in the reverse order.
  10. Refit the cover: put the plastic cover back on the (+) terminal, if your car has one.
  11. Recharge the battery: let the engine run for at least 30 minutes, either driving or with the car stationary, so the battery reaches an adequate state of charge.

Some functions, including Stop & Start, are not available until the battery is sufficiently charged.

Charging the battery using a battery charger

Keeping the battery at an adequate state of charge is essential for a long battery life. You may need to charge it if you only use your car for short journeys, or if the car will be off the road for several weeks. Contact a PEUGEOT dealer or a qualified workshop.

If you charge the battery yourself:

  • Use only a charger compatible with lead-acid batteries with a nominal voltage of 12 V.
  • Follow the instructions from the charger's manufacturer.
  • Never reverse the polarities.
  • You do not need to disconnect the battery.
  1. Ignition off: switch off the ignition.
  2. Consumers off: switch off all electrical consumers (audio system, lighting, wipers, etc.).
  3. Charger off: switch off charger B before connecting its cables to the battery, to avoid dangerous sparks.
  4. Check the cables: make sure the charger cables are in good condition.
  5. Uncover the terminal: raise the plastic cover on the (+) terminal, if your car has one.
  6. Red cable: connect the positive (+) red cable of charger B to the (+) terminal of battery A.
  7. Black cable: connect the negative (-) black cable to earth point C on the car.
  8. Finish charging: when charging is complete, switch off charger B before disconnecting the cables from battery A.

If the 12 V charger label is present, you must use only a 12 V charger, otherwise you could cause irreversible damage to the electrical components linked to the Stop & Start system. Never try to charge a frozen battery, as there is a risk of explosion. If the battery has frozen, have it checked by a PEUGEOT dealer or a qualified workshop, who will make sure the internal parts are not damaged and the case has not cracked, which could let toxic and corrosive acid leak out.

Disconnecting the battery

If your car is out of use for a long period, disconnecting the battery is recommended so it keeps enough charge to start the engine. You only need to disconnect the (+) terminal, which has a quick-release clamp.

Before disconnecting:

  1. Close everything: close all openings (doors, boot, windows, etc.).
  2. Consumers off: switch off all electrical consumers (audio system, wipers, lighting, etc.).
  3. Ignition off: switch off the ignition and wait for 4 minutes.

wait 2 minutes after switching off the ignition, and to close the windows and doors, before disconnecting the battery.

Disconnecting the (+) terminal:

  1. Release the clamp: raise lever A fully to release clamp B.
  2. Remove the clamp: lift clamp B off.

Reconnecting the (+) terminal:

  1. Open the lever: raise lever A fully.
  2. Fit the clamp: refit open clamp B on the (+) terminal.
  3. Seat the clamp: push clamp B fully down.
  4. Lock the clamp: lower lever A to lock clamp B.

Do not force the lever. It will not lock if the clamp is not positioned correctly, so start the procedure again.

After reconnecting: switch on the ignition and wait 1 minute before starting the engine, so the electronic systems can initialise. If minor problems remain after this, contact a PEUGEOT dealer or a qualified workshop. You will need to reset these yourself, reset these yourself:

  • the remote control key
  • the date and time
  • the radio preset stations

Frequently Asked Questions

Where is the negative terminal on my Peugeot 2008 battery?

The battery's (-) terminal is not accessible. Use the remote earth point on the right side of the engine mounting instead.

Can I push start a Peugeot 2008 with an automatic gearbox?

No. If your car has an electronic or automatic gearbox, never try to start the engine by pushing the car.

How long should I run the engine after a jump start?

Let the engine run for at least 30 minutes, either driving or with the car stationary, so the battery reaches an adequate state of charge.

Why is Stop & Start not working after a jump start?

Stop & Start is not available if the battery is not sufficiently charged. It may also not work on the journey after the first engine start until the car has been parked for a period of up to about 8 hours.

A flat battery is easy to sort out once you know the right order for connecting the leads and the safety steps to follow. Keep this guide handy, and if you are ever unsure, contact a PEUGEOT dealer or a qualified workshop.

More Peugeot 2008 Guides

If a battery problem brings up a lamp on your dashboard, see our guides to the Peugeot 2008 red warning lights, the Peugeot 2008 orange warning lights and the Peugeot 2008 green and blue indicator lamps.

Don't forget to follow us on Instagram for more Peugeot guides!

This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.

Related guides: Peugeot 2008 model guides.

Cover adapted from a photograph by Vauxford — Wikimedia Commons, CC BY-SA 4.0 (AI edited).

Related guides

Guide ·

Peugeot 2008 Bulb Replacement (2016-present)

Changing a bulb on your Peugeot 2008 is a job you can often do yourself, as long as you know which bulb goes where and how to reach it. This guide lists the front and rear lamps with their bulb types, explains …

Guide ·

Peugeot 2008 Gauges and Service Indicator (2016-present)

Your Peugeot 2008 has several gauges and indicators that show the state of the car between services. This guide explains the service indicator, the coolant temperature gauge, the oil level checks and the AdBlue…

Guide ·

Peugeot 2008 Fuse Box and Fuses (2016-present)

Your Peugeot 2008 has fuseboxes in the passenger compartment and under the bonnet. This guide shows you how to reach the fuse extraction tweezers, how to change a fuse safely, and which fuse protects which func…