Peugeot 508Updated 12 min read

Peugeot 508 II Spare Wheel and Tyre Repair Kit

How to use the tool kit, temporary puncture repair kit and space-saver spare wheel on your Peugeot 508 II. Covers the Peugeot 508 II (2018-2023).

Peugeot 508 (2018-2023) in a mountain lay-by with the boot open
Image adapted from a photo by Vauxford, CC BY-SA 4.0.

Hello and welcome. In this post, we'll look at where the spare wheel or tyre repair kit is, and how to use it after a puncture on the Peugeot 508 II (2018-2023). A flat tyre is never welcome, but your Peugeot 508 carries what you need to deal with it. This guide explains where the tool kit is stored, how to use the temporary puncture repair kit, and how to change a wheel using the space-saver spare wheel. It covers the Peugeot 508 II (2018-2023), including vehicles produced from 01/04/2021. Your car has either a temporary puncture repair kit or a spare wheel, and some tools depend on the version or equipment fitted, so not every item here will apply to your 508.

Where is the spare wheel on a Peugeot 508 II?

Depending on the version, the spare wheel or the tyre repair kit is stowed under the boot floor, with the tools beside it.

Peugeot 508 II spare wheel and tools stowed under the boot floor

Quick Reference

Scroll the table sideways.

SectionIn short
Tool kitWhere the tools are and what each one does
Temporary puncture repair kitRepairing a puncture and checking tyre pressures
Spare wheelRemoving, fitting and driving on the space-saver spare

Tool kit

The tool kit is supplied with the car and stored in the boot, under the floor. What it contains depends on your car's equipment: either a temporary puncture repair kit or a spare wheel.

Peugeot 508 II tyre repair kit: compressor, hose and sealant bottle

Hatchback:

  1. Open the boot: open the boot.
  2. Lift the floor: lift up the boot floor and fold it back on itself.

SW:

  1. Open the boot: open the boot.
  2. Lift the floor: lift up the boot floor.
  3. Hook it up: attach the floor hook to the upper boot seal.

Scroll the table sideways.

No.ToolWhat it is forFitted with
1Chock (depending on equipment)To immobilise the carAll versions
2Socket for the wheel security bolts, kept in the glove box (depending on equipment)To adapt the wheelbrace to the special security boltsAll versions
3Removable towing eyeFor towing the carAll versions
412 V compressor with cartridge of sealant and speed limit sticker (Kit 1 or Kit 2)Temporary tyre repair and adjusting tyre pressureTemporary puncture repair kit
5WheelbraceRemoving the wheel boltsSpare wheel
6Jack with integrated handleRaising the carSpare wheel
7Wheel bolt cap removal tool (depending on equipment)Removing the wheel bolt head finishers on alloy wheelsSpare wheel

These tools are specific to your car and can vary with the level of equipment, so do not use them for anything else. Only use the jack supplied with the car, and only to change a wheel with a damaged or punctured tyre. If your car no longer has its original jack, contact a PEUGEOT dealer or a qualified workshop to get the one the manufacturer intended. The jack meets European standards under the Machinery Directive 2006/42/CE and needs no maintenance.

Temporary puncture repair kit

The temporary puncture repair kit is made up of a compressor and a sealant cartridge. It lets you repair a tyre temporarily so you can drive to the nearest garage, and it is designed to repair most punctures on the tyre tread. Your car's electrical system can power the compressor from the 12 V socket for long enough to repair a tyre. The tyre inflation pressures are shown on the tyre pressure label.

Do not remove any foreign body, such as a nail or screw, that has gone into the tyre.

Before you start:

  1. Park safely: park without obstructing traffic and apply the parking brake.
  2. Stay visible: follow the safety rules of the country you are driving in, such as hazard warning lamps, warning triangle and high visibility jacket.
  3. Ignition off: switch off the ignition.

Connecting kit 1:

  1. Uncoil the pipe: uncoil the pipe stowed under the compressor.
  2. Connect the sealant: connect the pipe from the compressor to the bottle of sealant.
  3. Fit the bottle: turn the bottle of sealant over and secure it in the notch on the compressor.
  4. Valve cap off: remove the valve cap from the tyre and put it somewhere clean.
  5. Connect to the tyre: connect the pipe from the bottle of sealant to the tyre valve and tighten firmly.

Connecting kit 2:

  1. Remove the cap: remove the transparent cap from the bottle of sealant.
  2. Lift the cover: lift the protective cover on the compressor.
  3. Fit the bottle: turn the bottle of sealant over and screw it a quarter turn into the compressor.
  4. Valve cap off: remove the valve cap from the tyre and put it somewhere clean.
  5. Uncoil the pipe: uncoil the pipe stowed under the compressor.
  6. Connect to the tyre: connect the pipe from the compressor to the tyre valve and tighten firmly.

Repairing the tyre:

  1. Check the switch: make sure the compressor switch is in position "O".
  2. Uncoil the cable: fully uncoil the electric cable stowed under the compressor.
  3. Plug in: connect the compressor's plug to the car's 12 V socket.
  4. Fit the sticker: stick the speed limit sticker inside the car close to the driver, as a reminder that a wheel is in temporary use.
  5. Ignition on: switch on the ignition.
  6. Inflate: move the switch to position "I" until the tyre pressure reaches 2 bar. The sealant is injected into the tyre under pressure, so do not disconnect the pipe from the valve during this step (risk of blowback). If 2 bar is not reached after approximately 7 minutes, the tyre cannot be repaired: contact a PEUGEOT dealer or a qualified workshop for help.
  7. Switch off: move the switch to position "O".
  8. Unplug: disconnect the compressor's plug from the 12 V socket.
  9. Remove the kit: remove the kit.
  10. Valve cap on: refit the cap on the valve.
  11. Store the bottle: remove and store the bottle of sealant.
  12. Drive straight away: drive immediately for approximately 3 miles (5 kilometres) at reduced speed, between 12 and 37 mph (20 and 60 km/h), to plug the puncture.
  13. Check the pressure: stop and check the repair and the tyre pressure using the kit. If the pressure is incorrect, contact a PEUGEOT dealer to have the tyre changed.
  14. Drive again: if the pressure is correct, drive a second time for approximately 3 miles (5 kilometres) at between 12 and 37 mph (20 and 60 km/h).
  15. Confirm the repair: stop and check the tyre pressure again using the kit to confirm the repair has worked.

The sealant is harmful if swallowed and irritates the eyes, so keep it out of the reach of children. The use-by date is marked on the bottle. Do not throw the used bottle away in the environment: take it to a PEUGEOT dealer or an authorised waste disposal site, and remember to get a new bottle from a PEUGEOT dealer or a qualified workshop.

With a tyre repaired using this kit, do not exceed 50 mph (80 km/h) and do not drive more than 125 miles (200 km). You must contact a PEUGEOT dealer or a qualified workshop to have the repair checked and the tyre changed.

Checking or adjusting tyre pressures: you can also use the compressor without sealant.

  1. Valve cap off: remove the valve cap and keep it somewhere clean.
  2. Uncoil the pipe: uncoil the pipe stowed under the compressor.
  3. Connect: screw the pipe onto the valve and tighten firmly.
  4. Check the switch: make sure the compressor switch is in position "O".
  5. Uncoil the cable: fully uncoil the electric cable stowed under the compressor.
  6. Plug in: connect the compressor's plug to the car's 12 V socket.
  7. Ignition on: switch on the ignition.
  8. Adjust: move the switch to position "I" and adjust the pressure to the value on the tyre pressure label. To let air out, press the black button on the compressor pipe, near the valve connection. If 2 bar is not reached after 7 minutes, the tyre is damaged: contact a PEUGEOT dealer or a qualified workshop for help.
  9. Switch off: once the correct pressure is reached, move the switch to position "O".
  10. Stow the kit: remove the kit and stow it.
  11. Valve cap on: refit the cap on the valve.

If you adjust the pressure of one or more tyres, you need to reinitialise the under-inflation detection system.

Spare wheel

The spare wheel is a space-saver wheel stored in the boot, under the floor. To reach it, first open the boot floor as described in the Tool kit section.

Removing the spare wheel:

  1. Slacken: slacken the central nut.
  2. Remove the fastening: remove the fastening device (nut and bolt).
  3. Lift: lift the spare wheel towards the back of the boot.
  4. Take it out: take the wheel out of the boot.

Putting the spare wheel back: the punctured wheel cannot be stored under the boot floor. A polystyrene block in the bottom of the well raises the wheel and stops the boot floor dropping down.

  1. Position the wheel: put the spare wheel back in its housing.
  2. Loosen the nut: slacken the nut on the bolt by a few turns.
  3. Fit the fastening: position the fastening device (nut and bolt) in the middle of the wheel.
  4. Tighten: tighten the central nut enough to hold the wheel correctly.
  5. Refit the tool box: put the tool box back in the middle of the wheel and clip it in place.

Parking safely first: stop where you do not obstruct traffic, on level, stable and non-slippery ground. With an automatic gearbox, select mode P, apply the parking brake unless it is in automatic mode, and switch off the ignition. Check that the parking brake indicator lamps on the instrument panel are on fixed. Everyone must get out and wait somewhere safe. If necessary, place a chock under the wheel diagonally opposite the one you are changing. Never go under a car raised on a jack: use an axle stand.

If your wheel has a wheel trim, pull it off at the valve hole using the wheelbrace before removing the wheel. To refit it, line up its hole with the valve, then push it into place all round the edge with the palm of your hand.

Removing a wheel:

  1. Bolt covers off: on alloy wheels, remove the cover from each bolt using tool 7.
  2. Security bolt: fit security socket 2 on wheelbrace 5 and slacken the security bolt.
  3. Other bolts: slacken the other bolts using wheelbrace 5 only.
  4. Place the jack: put the foot of jack 6 on the ground directly below the front jacking point A or rear jacking point B, whichever is closest to the wheel.
  5. Extend the jack: extend jack 6 until its head touches jacking point A or B. The contact area must sit properly in the central part of the jack head.
  6. Raise the car: raise the car until there is enough space under the wheel to fit the spare (not punctured) wheel easily.
  7. Remove the bolts: remove the bolts and keep them somewhere clean.
  8. Remove the wheel: take the wheel off.

Make sure the jack is stable: on slippery or loose ground it can slip or collapse, with a risk of injury. Only use jacking points A or B, with the jack head centred under the contact area, or you risk damaging the car or the jack collapsing.

Fitting a wheel: if your car has alloy wheels, the bolt washers A do not touch a steel or space-saver spare wheel. The wheel is held by the conical contact surface B of each bolt.

  1. Fit the wheel: fit the wheel on the hub.
  2. Hand-tighten: screw in the bolts by hand as far as possible.
  3. Pre-tighten the security bolt: use wheelbrace 5 with security socket 2.
  4. Pre-tighten the others: use wheelbrace 5 only.
  5. Lower the car: lower the car fully.
  6. Remove the jack: fold jack 6 and remove it.
  7. Tighten the security bolt: use wheelbrace 5 with security socket 2.
  8. Tighten the others: use wheelbrace 5 only.
  9. Bolt covers on: refit the bolt covers (depending on equipment).
  10. Store the tools: put the tools away.

After changing a wheel: with a space-saver spare wheel, deactivate certain driving aids, such as Active Safety Brake and Adaptive cruise control. Do not exceed 50 mph (80 km/h) or drive more than 50 miles (80 km), and never drive with more than one space-saver wheel fitted. Go to a PEUGEOT dealer or a qualified workshop to have the spare wheel's bolt tightening and tyre pressure checked, and to have the punctured tyre examined. The technician will tell you whether it can be repaired or must be replaced.

Frequently Asked Questions

Where is the jack on a Peugeot 508?

On cars with a spare wheel, the jack is part of the tool kit stored in the boot, under the floor. Only use the jack supplied with your car.

How fast can I drive on a Peugeot 508 space-saver spare wheel?

Do not exceed 50 mph (80 km/h) or drive more than 50 miles (80 km). You should also deactivate certain driving aids, such as Active Safety Brake and Adaptive cruise control.

How far can I drive after using the Peugeot 508 puncture repair kit?

With a tyre repaired using the kit, do not exceed 50 mph (80 km/h) and do not drive more than 125 miles (200 km). Have the repair checked and the tyre changed by a PEUGEOT dealer or a qualified workshop.

What if the tyre won't reach 2 bar with the repair kit?

If 2 bar is not reached after approximately 7 minutes, the tyre cannot be repaired. Contact a PEUGEOT dealer or a qualified workshop for help.

Whether your 508 has a repair kit or a space-saver spare, both are only a temporary fix to get you to a garage. Keep to the speed and distance limits, and have the tyre checked by a PEUGEOT dealer or a qualified workshop as soon as you can.

More Peugeot 508 Guides

To understand what your dashboard is telling you, read our guides to the Peugeot 508 red warning lights, the Peugeot 508 orange warning lights and the Peugeot 508 green and blue indicator lamps.

Don't forget to follow us on Instagram for more Peugeot guides!

This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.

Related guides: Peugeot 508 model guides.

Cover adapted from a photograph by Vauxford — Wikimedia Commons, CC BY-SA 4.0 (AI edited).

Related guides

Guide ·

Peugeot 508 II 12V Battery and Jump Starting

Hello and welcome. This article covers the 12 V battery on the Peugeot 508 II (2018-2023): reaching it, jump starting, charging with a charger, and disconnecting and reconnecting it. We also look at t

Guide ·

Peugeot 508 II Tyre Pressure

Hello and welcome. This article looks at the under-inflation detection system on the Peugeot 508 II (2018-2023). We cover what the alert means, reinitialising the system after adjusting pressures, and

Guide ·

Peugeot 508 I 12V Battery and Jump Starting

Hello and welcome. In this post we look at the 12 V battery on the Peugeot 508 I (2014-present). We cover jump starting from another battery, charging with a charger, disconnecting and reconnecting, a