Peugeot 508 II 12V Battery and Jump Starting
Hello and welcome. This article covers the 12 V battery on the Peugeot 508 II (2018-2023): reaching it, jump starting, charging with a charger, and disconnecting and reconnecting it. We also look at t
How to start, drive and park your Peugeot 508 II: EAT6/EAT8 and e-EAT8 gearbox, electric parking brake, driving modes and Stop & Start explained.

Hello and welcome. In this post, we'll look at starting, the gearbox and Stop & Start on the Peugeot 508 II (2018-2023). It also covers the on safe driving, flooded roads and towing. It covers the Peugeot 508 II (2018-2023), including vehicles produced from 01/04/2021. Some functions depend on the engine, version or equipment, so not everything here applies to every 508.
Hold the remote control against the back-up reader on the steering column, select mode P and press the brake pedal, then press the START/STOP button.
Scroll the table sideways.
| Section | In short |
|---|---|
| Driving recommendations | Safe driving, flooded roads and towing advice |
| Starting/switching off the engine | Keyless starting, switching off and back-up starting |
| Electric parking brake | Applying, releasing and deactivating automatic parking brake |
| Automatic gearbox (EAT6 / EAT8) | Push selector, paddles, manual mode and moving off |
| e-EAT8 electric automatic gearbox (Rechargeable hybrid) | Hybrid gearbox positions and regenerative braking B mode |
| Hill start assist | Holds the car briefly when starting on a slope |
| Driving modes | Eco, Comfort, Sport, Electric and Hybrid modes explained |
| Stop & Start | How Stop & Start stops, restarts and switches off |
Here are some basic rules for driving your 508 safely
Important safety warnings:
On PSE (PEUGEOT Sport Engineered) versions, repeated hard braking can cause loud banging noises, which are completely normal. Keep driving but brake more lightly so the braking system can cool down. Braking performance is not affected.
On flooded roads: avoid it where you can, as water can seriously damage the engine or electric motor, the gearbox and the electrical systems. If you really must drive through a flooded section:
If you are unsure about the state of your car afterwards, contact a PEUGEOT dealer or a qualified workshop.
Towing: a trailer puts extra demands on your car, so take particular care.
Before setting off with a trailer:
With a genuine PEUGEOT towing device, the rear parking sensors are deactivated automatically so they do not sound.
The electronic key must be inside the passenger compartment. If it is not detected, a message appears: move the key so the engine can be started or switched off. If the problem continues, use back-up starting, described below.

Starting:
On Diesel engines, in sub-zero temperatures and/or when the engine is cold, the engine only starts once the preheating warning lamp goes out. If this lamp comes on after you press "START/STOP", keep the pedal fully pressed and do not press the button again until the engine is running.
If a starting condition is not met, a message appears. Sometimes a message asks you to turn the steering wheel while pressing "START/STOP" to help unlock the steering column. On Petrol engines, after a cold start, preheating the catalytic converter can cause noticeable engine vibrations for up to 2 minutes (accelerated idle speed).
Starting a rechargeable hybrid:
To leave Park mode, wait for the READY lamp to come on. The system starts in Electric mode by default and decides whether to start the petrol engine depending on things like battery charge and outside temperature. You can change the driving mode at any time with the mode selector. In electric mode the car is silent, so watch out for pedestrians and cyclists who may not hear you, even with the pedestrian horn.
Switching off:
Sometimes you need to turn the steering wheel to lock the steering column. On some versions with an EAT6/EAT8 gearbox, the steering column does not lock, but the gearbox locks in mode P. If the car is not immobilised, the engine will not stop. Remember that with the engine off, braking and steering assistance are cut, so you could lose control. Never leave the car with the electronic key inside.
Ignition on without starting: with the key in the car, press "START/STOP" without pressing any pedal. Press it again to switch the ignition off so the car can be locked.
Back-up starting: a back-up reader on the steering column lets you start the engine if the key is not detected or its battery is flat.
In automatic mode, the electric parking brake applies itself when you switch off the engine and releases when you move off. Automatic mode is on by default. With the engine running, you can always briefly pull the control to apply the brake, or briefly push it while pressing the brake pedal to release it.
Indicator lamp: the lamp on the instrument panel and on the control comes on with the message "Parking brake applied" and goes out with "Parking brake released". It flashes when you make a manual request to apply or release the brake.
Safety warnings:
Manual release (ignition on or engine running):
If the brake pedal is not pressed, the parking brake stays on and a message appears. For manual application, with the car stationary, briefly pull the control. The control lamp flashes to confirm.
Automatic release: make sure the engine is running and the driver's door is closed. The brake releases gradually as you move off. With an automatic gearbox:
If the brake does not release, check that the front doors are fully closed. When stationary with the engine running, do not press the accelerator unnecessarily, as this can release the parking brake.
Automatic application: with the car stationary, the brake applies when you switch off the engine. It does not apply if the engine stalls or goes into STOP mode with Stop & Start. You can still apply or release it manually at any time.
Special cases:
Deactivating automatic operation: you may need to do this when it is extremely cold or when towing (for example a caravan, or a breakdown).
From then on, you can only apply and release the brake manually. Repeat the same procedure to reactivate automatic operation; the lamp on the instrument panel goes out to confirm.
The EAT6 or EAT8 is a 6 or 8-speed automatic gearbox with a push selector. It also has a manual mode, with gear changes using paddles behind the steering wheel.
Scroll the table sideways.
| Position | What it does |
|---|---|
| P (Park) | For parking: the front wheels are blocked. |
| R (Reverse) | Reverse gear. |
| N (Neutral) | For moving the car with the ignition off, or to let it free-wheel. |
| D (Automatic) | The gearbox changes gear based on driving style, road profile and load. |
| M (Manual) | You change gear using the steering-mounted controls. |
On the push selector:
Push the selector forwards (N or R) or rearwards (N or D) once or twice, passing the point of resistance if needed. It springs back when you let go. For example, to go from P to R while pressing Unlock, push forward twice without crossing the point of resistance (P to N, then N to R), or once crossing it (straight from P to R).
Paddles: in mode M or D, pull the "+" or "-" paddle towards you and release to change up or down. The paddles cannot select neutral or engage or disengage reverse.
Instrument panel display:
If you open the driver's door with the ignition on, a message prompts you to select mode P. If you need to press the brake and/or Unlock to change mode, a message tells you. Only appropriate mode changes are accepted.
Warnings: with the engine running and the brakes released, the car moves off in R, D or M even without the accelerator. Never press the accelerator and brake at the same time, as this can damage the gearbox. If the battery fails, place the supplied chock against one of the wheels.
Unlocking from mode P:
Unlocking from N, below 3 mph (5 km/h):
Engaging reverse:
Permanent manual mode: on EAT6 and EAT8 without the Full Park Assist button, start in D and press button M (its green lamp comes on). On EAT8 with the Full Park Assist button, press the DRIVE MODE control and select "Manual". To leave, push forwards once to return to D, press button M (its lamp goes off), or choose another mode with DRIVE MODE.
The car must be stationary to switch off the ignition. If you open the driver's door in mode N, an audible signal sounds until you close it.
Automatic mode: the gearbox picks the best gear for ambient temperature, road profile, load and driving style. For maximum acceleration, press the accelerator fully (kick-down); the gearbox changes down or holds the gear until maximum engine speed. You can use the paddles to choose a gear temporarily if speed and engine speed allow. In manual mode, the gearbox only changes gear if speed and engine speed allow.
Moving off from P:
Moving off from N:
The car moves off immediately. Never try to start the engine by pushing the car.
Switching off: mode P engages automatically when you switch off the ignition, whatever mode you are in. In mode N, P engages after 5 seconds, to allow free-wheeling. Check that P is engaged and the parking brake has applied; if not, apply it manually. The lamps on the gear selector, the parking brake control and the instrument panel must all be on.
Rechargeable hybrid versions have the e-EAT8, an 8-speed automatic gearbox with a push selector and regenerative braking. Apart from manual mode and regenerative braking, it works in the same way as the other EAT8 gearboxes.
Scroll the table sideways.
| Position | What it does |
|---|---|
| P (Park) | For parking: the front wheels are blocked. |
| R (Reverse) | Reverse gear. |
| N (Neutral) | For moving the car with the ignition off, for example in some car washes or when it is being towed. |
| D/B | Automatic forward gear (D), or with regenerative braking (B), where the gearbox also brakes when you release the accelerator. |
The push selector has a P button, an Unlock button (press and hold it, with your foot on the brake, to leave P or select R) and lamps for R, N and D/B. To leave Park mode, wait for the READY lamp to come on.
Instrument panel display:
In all-electric driving, the gear engaged is not shown. The gearbox state stays on the display for a few seconds after you switch off the ignition.
Regenerative braking: this imitates engine braking, so the car slows down more quickly when you release the accelerator, without using the brake pedal. The recovered energy partly recharges the traction battery, although this does not show on the charge level indicator. This slowing down does not switch on the brake lamps.
The setting is not saved when you switch off the ignition.
Hill start assist holds your car still for about 2 seconds on a hill start, while you move your foot from the brake to the accelerator. It only works when:
Facing uphill with the car stationary, it holds the car briefly when you release the brake pedal, if mode D or M is selected on an automatic gearbox.
Do not get out of the car while hill start assist is holding it. If someone needs to get out with the engine running, apply the parking brake manually and check that the parking brake lamp and the P lamp on the control are on fixed. The system cannot be switched off, but applying the parking brake interrupts it.
The modes available depend on your car's engine and equipment. Press the control to show the modes on the instrument panel, then press it again to change mode. When the message disappears, the mode is active and stays shown on the instrument panel (except Normal).
Petrol and Diesel engines: Normal mode is selected every time you switch on the ignition.
Scroll the table sideways.
| Mode | What it does |
|---|---|
| Eco | Reduces energy use by lowering heating and air conditioning performance, without switching them off. |
| Comfort | More comfortable driving and softer suspension. |
| Normal | Restores the default settings. With Active Suspension Control, the best balance of comfort and handling. |
| Sport | More dynamic driving, acting on power steering, Active Suspension Control, accelerator and gear changes (automatic gearbox), with the option to show dynamic settings on the instrument panel. |
| Manual | Permanent manual mode with an automatic gearbox and Full Park Assist, using the steering wheel paddles. |
Coasting mode: depending on version or engine, with an EAT8 gearbox in mode D and in any mode except Sport, gradually and fully releasing the accelerator lets the car free-wheel, which can save fuel. A drop in engine speed and engine noise is normal.
Rechargeable hybrid engines: Electric mode is selected every time you switch on the ignition.
Electric: drives on 100% electrical energy, up to about 84 mph (135 km/h). If conditions do not allow Electric mode when you start, the message "Electric mode currently unavailable" appears and the car switches to Hybrid mode. In some countries, an LED under the interior mirror, visible from outside, confirms Electric mode. You can deactivate it by inserting the tip of a paper clip or similar into the hole under the mirror.
If the petrol engine starts several times without warming up enough, Electric mode may be temporarily unavailable, because of fuel diluting in the oil. The message "Electric mode unavailable: automatic operation in progress" appears. To get normal electric operation back, drive about 50 miles (80 km) in motorway conditions or about 125 miles (200 km) in town. This causes no mechanical or electrical damage and can happen several times in the car's life.
Hybrid: optimises fuel consumption by running the two types of engine alternately or at the same time, depending on driving conditions and style. You can still drive on 100% electric power if the battery has enough charge and you accelerate moderately. Depending on equipment, it is combined with the Normal mode of Active Suspension Control.
Sport: more dynamic driving for maximum performance. Electric power supplements the petrol engine while there is energy in the battery. Depending on equipment, it is combined with the Sport mode of Active Suspension Control. On PSE (PEUGEOT Sport Engineered) versions, electrical energy either supplements the petrol engine or recharges the traction battery, depending on how you drive, and specific settings for power steering, accelerator sensitivity and ESC make the most of the car's performance.
Comfort: depending on equipment, combines Hybrid mode with the Comfort mode of Active Suspension Control.
Stop & Start puts the engine into standby (STOP mode) when the car is stationary, for example at red lights or in traffic jams, and restarts it (START mode) as soon as you want to move off. It is mainly designed for town driving, to cut fuel consumption, exhaust emissions and noise when stationary. It does not affect the car's functions, in particular the braking.

Switching it off or on: the function is on by default when you switch on the ignition. Press the button to deactivate or reactivate it. A message confirms the change. When it is off, the orange lamp is lit, and if the engine was in standby it restarts straight away. A separate lamp shows when the function is on.
Safety: deactivate Stop & Start before doing anything under the bonnet, so the engine cannot restart and injure you. It is also strongly recommended to deactivate it before driving into a flooded area.
Main conditions for it to work:
When the engine goes into STOP mode (automatic gearbox):
A time counter adds up the time spent in standby during the journey and resets each time you switch on the ignition.
The engine will not go into standby if the conditions above are not met, on a steep slope (up or down), when needed to keep the cabin comfortable, or when demisting is active. In these cases the lamp flashes for a few seconds, then goes off. After a restart, STOP mode is not available until you reach 5 mph (8 km/h). When parking, it is not available for a few seconds after leaving reverse or turning the steering wheel.
When the engine restarts (automatic gearbox):
The engine also restarts automatically if the conditions are met again, or if the car goes above 0.6 mph (1 km/h) in mode N. In these cases the lamp flashes for a few seconds, then goes off.
Hold the remote control against the back-up reader on the steering column, select mode P and press the brake pedal, then press the "START/STOP" button.
The engine must be running and the driver's door closed. If it still does not release, check that both front doors are fully closed.
It needs enough battery charge and an outside temperature between about -5°C and 45°C. If you see "Electric mode unavailable: automatic operation in progress", drive about 50 miles (80 km) on the motorway or about 125 miles (200 km) in town to restore it.
It needs the driver's door closed, the seat belt fastened, enough battery charge, a warm engine and an outside temperature between 0°C and 35°C. It also stays running on steep slopes, when demisting or when needed to keep the cabin comfortable.
Knowing how the gearbox, parking brake, driving modes and Stop & Start work on your Peugeot 508 makes everyday driving easier and safer. Keep this guide handy. If in doubt, ask a PEUGEOT dealer or a qualified workshop.
If a lamp comes on while you are driving, see our guides to Peugeot 508 red warning lights, Peugeot 508 orange warning lights and Peugeot 508 green and blue indicator lamps.
Don't forget to follow us on Instagram for more Peugeot guides!
This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.
Related guides: Peugeot 508 model guides.
Cover adapted from a photograph by Vauxford — Wikimedia Commons, CC BY-SA 4.0 (AI edited).
Hello and welcome. This article covers the 12 V battery on the Peugeot 508 II (2018-2023): reaching it, jump starting, charging with a charger, and disconnecting and reconnecting it. We also look at t
Hello and welcome. This article looks at the under-inflation detection system on the Peugeot 508 II (2018-2023). We cover what the alert means, reinitialising the system after adjusting pressures, and
Hello and welcome. In this post we look at the 12 V battery on the Peugeot 508 I (2014-present). We cover jump starting from another battery, charging with a charger, disconnecting and reconnecting, a