Guide-me-home lighting
With the ring in "AUTO" and in poor light, the dipped beam headlamps come on automatically when you switch off the ignition. You can activate or deactivate this function and set its duration in the Driving/Vehicle touch screen menu.
Welcome lighting
When you unlock the car in low ambient light, with the "Automatic illumination of headlamps" function activated, certain exterior lamps and certain passenger compartment lamps come on automatically. You can activate or deactivate this function and set its duration in the Driving / Vehicle touch screen menu.
Door mirror spotlamps
These spotlamps light the ground near the front doors to make getting in easier. With the front courtesy lamp switch in the relevant position, they come on automatically:
- when the vehicle is unlocked.
- when a door is opened.
- when the remote control sends a request to locate the vehicle.
Whatever the switch position, they also come on with the welcome and guide-me-home lighting. They go off automatically after 30 seconds.
Automatic lighting systems - General recommendations
The automatic lighting systems use a detection camera at the top of the windscreen.
The system can be disrupted or not work correctly:
- When visibility is poor, for example in snowfall or heavy rain.
- If the windscreen in front of the camera is dirty, misted up or masked, for example by a sticker.
- If the car is facing highly reflective signs or safety barrier reflectors.
The system cannot detect:
- Road users without their own lighting, such as pedestrians.
- Vehicles with hidden lighting, for example behind a safety barrier on the motorway.
- Vehicles at the top or bottom of a steep slope, on winding roads or on crossroads.
Clean the windscreen regularly, especially in front of the camera. The inside of the windscreen can mist up around the camera, so demist it regularly in humid and cold weather. Do not let snow build up on the bonnet or roof, as it could block the camera.
Automatic headlamp dipping
With the ring in "AUTO" and the function activated on the touch screen, this system switches automatically between dipped and main beam headlamps, according to lighting and traffic conditions. It uses the camera at the top of the windscreen, so the general recommendations for automatic lighting systems also apply.
This system is a driving aid. You remain responsible for your car's lighting, for using it correctly in the light, visibility and traffic conditions, and for following driving and vehicle regulations.
- The system becomes operational above 16 mph (25 km/h).
- Below 9 mph (15 km/h), the function is no longer operational.
Activation/Deactivation
Change the settings in the Driving/Vehicle touch screen menu. The system's state is stored when you switch off the ignition.
Operation
- Very low light, traffic permitting: the main beam headlamps come on automatically and the matching indicator lamps light up.
- Sufficient light and/or traffic not allowing main beam: the dipped beam headlamps stay on and the matching indicator lamps light up.
The function is deactivated if you switch on the foglamps or if the system detects poor visibility, such as fog, heavy rain or snowfall. It reactivates automatically once the foglamps are off or visibility improves. The indicator lamp goes out when the function is deactivated.
Pause
You can take over at any time if you need to change the headlamp beam.
- Pause: switch the headlamps manually between dipped and main beam. If the "AUTO" and "Dipped beam" indicator lamps were on, the system changes to main beam. If the "AUTO" and "Main beam" indicator lamps were on, it changes to dipped beam.
- Reactivate: switch the headlamps manually between dipped and main beam again.
Static cornering lighting
With the dipped or main beam headlamps on, this function uses LEDs to light the inside of a bend. Your speed must be below 56 mph (90 km/h), and it is only available with "Full LED" technology headlamps. You set it in the Driving / Vehicle touch screen menu.
It works from a certain angle of steering wheel rotation. It does not operate:
- below a certain angle of steering wheel rotation.
- above 56 mph (90 km/h).
- when reverse gear is engaged.
Frequently Asked Questions
Why won't my Peugeot 3008 rear foglamps switch on?
The rear foglamps only work when the dipped or main beam headlamps are on. Once they are, rotate the ring on the lighting control stalk forwards to turn the foglamps on.
Why don't my 3008 headlights come on automatically in fog?
In fog or snow, the rain/sunshine sensor can detect enough light, so the lighting does not come on automatically. Switch the lights on manually in these conditions.
What beam height setting should I use on my Peugeot 3008?
Use position 0 for the driver alone or with a front passenger, 1 for 5 people, 3 for 5 people with load in the boot, and 5 for the driver alone with load in the boot. Positions 2, 4 and 6 are not used.
Why has automatic main beam stopped working on my 3008?
The function is deactivated when the foglamps are on, when visibility is poor or below 9 mph (15 km/h). It also pauses if you switch between dipped and main beam manually, and you switch manually again to reactivate it.
Knowing how your 3008's lights work helps you see clearly and avoid dazzling other drivers. Keep the windscreen clean in front of the camera and sensor, and if in doubt about a lighting function, ask a PEUGEOT dealer or a qualified workshop.
More Peugeot 3008 Guides
If a lamp lights up on your instrument panel, see our guides to Peugeot 3008 red warning lights, Peugeot 3008 orange warning lights and Peugeot 3008 green and blue indicator lamps.
Don't forget to follow us on Instagram for more Peugeot guides!
This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.
Related guides: Peugeot 3008 model guides.
Cover adapted from a photograph by Tokumeigakarinoaoshima — Wikimedia Commons, CC BY-SA 4.0 (AI edited).