Peugeot 308 Fuse Box and Fuses (2021-2025)
Hello and welcome. In this article we look at the fuses on the Peugeot 308 III (2021-2025). We will cover who should change a fuse and what to know before fitting extra electrical equipment or accesso
How to start, park and drive your Peugeot 308 III: electric parking brake, EAT8 and e-DCS gearboxes, driving modes and Stop & Start,.

Hello and welcome. In this post, we'll look at starting the engine, the electric parking brake, the gearbox and Stop & Start on the Peugeot 308 III (2021-2025). It covers driving advice, starting and switching off the engine, the electric parking brake, the automatic gearboxes and drive selector, the driving modes and the Stop & Start function. It covers the Peugeot 308 III (2021-2025), including vehicles produced from 07/08/2023. Many items depend on the engine, version or equipment fitted, so not everything here will apply to your 308. Many items depend on the engine, version or equipment fitted, so not everything here will apply to your 308.
Switch it off from the driving-assist controls or touchscreen; an amber A OFF tell-tale shows that Stop & Start is off until you turn it back on.

Scroll the table sideways.
| Section | In short |
|---|---|
| Driving recommendations | Safe driving rules, fire risks and flooded roads |
| Starting/switching off the engine | How to start and stop with the electronic key |
| Electric parking brake | Applying, releasing and automatic mode of the parking brake |
| Automatic gearbox (EAT8/e-EAT8) | Using the EAT8 push selector, paddles and display |
| Electric dual-clutch automatic gearbox (e-DCS6/7) | Hybrid dual-clutch gearbox, electric motor and e-functions |
| Drive selector (Electric) | Electric version selector modes and how to use them |
| Driving modes | Normal, Eco, Sport, Electric and Hybrid modes explained |
| Stop & Start (Petrol or Diesel) | How Stop & Start works and when it won't |
gives a few basic rules for driving your 308 safely.
Important safety points:
On flooded roads: avoid it where you can, as it could seriously damage the engine or electric motor, the gearbox and the electrical systems. If you absolutely must drive through a flooded section:
If you are in any doubt about the state of your car afterwards, contact a PEUGEOT dealer or a qualified workshop.
Noise (Electric): electric versions are very quiet when driving, so you need to pay particular attention and always check the car's immediate surroundings when manoeuvring. At speeds of up to 19 mph (30 km/h), the pedestrian horn warns other road users that the car is there.
The electronic key must be inside the passenger compartment, and it is also detected in the boot. If the key is not detected, a message appears: move the key so the engine can be started or switched off. If there is still a problem, follow the Key not detected – Back-up starting or Back-up switch-off steps below.
Starting:
Diesel engines: in low temperatures or when the engine is cold, the engine starts only after the preheating warning lamp goes out. If this lamp comes on after you press START/STOP, keep the pedal fully depressed and do not press the button again until the engine is running at a stabilised speed.
If any starting condition is not met, a message is displayed. Sometimes a message asks you to turn the steering wheel while pressing START/STOP to help unlock the steering column.
Starting rechargeable hybrid vehicles:
Wait for the READY lamp before you exit Park mode. The system starts in Electric mode by default and decides whether the petrol engine needs to start, depending on things such as the battery charge level or outside temperature. You can change the driving mode at any time with the mode selector. When the car starts in electric mode it makes no noise, so watch out for pedestrians and cyclists, who may not hear it coming despite the pedestrian horn.
Switching off:
The automatic gearbox locks in mode P, and sometimes you need to turn the steering wheel to lock the steering column. If the car is not immobilised, the engine will not stop. Remember that with the engine off, braking and steering assistance are also cut off, so there is a risk of losing control of the car.
In automatic mode, the electric parking brake applies itself when you switch off the engine and releases when you move off. Automatic mode is on by default, but it can be deactivated in certain situations. You must still apply the parking brake whenever the car is stationary.

At any time with the engine running, briefly pull the control to apply the brake, or briefly push it while pressing the brake pedal to release it.
Indicator lamp: the lamp on the instrument panel and on the control comes on with the message "Parking brake applied", and goes out with the message "Parking brake released". It flashes when you make a manual request to apply or release the brake.
Manual release (ignition on or engine running):
If you do not press the brake pedal, the parking brake stays on and a message is displayed.
Manual application: with the car stationary, briefly pull the control. The control's indicator lamp flashes to confirm the request.
Automatic release: make sure the engine is running and the driver's door is closed. The brake then releases gradually as you move off.
With an automatic gearbox or drive selector, if the brake does not release automatically, check that the front doors are properly closed. When stationary with the engine running, do not press the accelerator unnecessarily, as this risks releasing the parking brake.
Automatic application: with the car stationary, the brake applies itself when you switch off the engine. It does not apply automatically if the engine stalls or goes into STOP mode with Stop & Start. In automatic mode you can still apply or release the brake by hand at any time using the control.
On petrol and Diesel versions, the EAT8 is an 8-speed automatic gearbox with a push selector and a manual mode using paddles behind the steering wheel. On rechargeable hybrid versions, it is an 8-speed automatic with a push selector and a regenerative braking function. Apart from the manual mode and the regenerative braking function, it works the same as the other EAT8 gearboxes.
Scroll the table sideways.
| Mode | What it does |
|---|---|
| P (Auto Park) | Press this button for Parking mode. The front wheels are blocked. |
| R | Reverse |
| N | Neutral, to free-wheel and move the car with the ignition off (see the Free-wheeling section below) |
| D | Automatic mode: the gearbox changes gear according to driving style, road profile and load |
| M (Petrol / Diesel) | Press this button for manual mode: you change gear with the steering-mounted controls |
| B (Rechargeable hybrid) | Press this button for regenerative braking: the gearbox also manages braking when you release the accelerator |
Using the selector:
Quick change between D and R (to avoid mode N):
Steering-mounted controls (depending on equipment): in mode M or D, pull the "+" or "-" paddle towards you and release it to shift up or down a gear. The paddles cannot select neutral or engage or disengage reverse.
Scroll the table sideways.
| Display | Meaning |
|---|---|
| P | Parking |
| R | Reverse |
| N | Neutral |
| D1.8 | Automatic forward gear |
| B1.8 | Automatic forward gear with regenerative braking activated |
| M1.8 | Manual forward gear |
In all-electric driving, the gear engaged is not shown. The gearbox status stays on the instrument panel for a few seconds after you switch off the ignition.
Operation: only appropriate mode changes are accepted. If you need to press the brake pedal to change mode with the engine running, an alert message appears.
Automatic mode: the gearbox picks the gear that gives optimal performance based on ambient temperature, road profile, load and driving style. For maximum acceleration, press the accelerator fully down (kick-down): the gearbox changes down or holds the gear until maximum engine speed. The paddles let you select a gear temporarily if vehicle and engine speed allow.
Manual mode: the gearbox changes gear only if vehicle speed and engine speed allow.
Regenerative braking (Rechargeable hybrid): the Brake function emulates engine braking, so the car slows down more quickly when you release the accelerator, without you pressing the brake pedal.
The e-DCS6 is a 6-speed electrified dual-clutch automatic gearbox for hybrid vehicles, and the e-DCS7 is a 7-speed version for rechargeable hybrid vehicles. Both use a push selector and offer a manual mode with paddles behind the steering wheel. The gearbox includes an electric motor, which improves the petrol engine's performance, reduces fuel consumption and allows all-electric driving.
Scroll the table sideways.
| Mode | What it does |
|---|---|
| P (Auto Park) | Press this button for Parking mode. The front wheels are blocked. |
| R | Reverse |
| N | Neutral, to free-wheel and move the car with the ignition off (see the Free-wheeling section below) |
| D | Automatic mode: the gearbox changes gear according to driving style, road profile and load |
| M (Hybrid) | Press this button for manual mode: you change gear with the steering-mounted controls |
| B (Rechargeable hybrid) | Press this button for regenerative braking: the gearbox also manages braking when you release the accelerator |
Using the selector:
Quick change between D and R (to avoid mode N):
Steering-mounted controls (depending on equipment): in mode M or D, pull the "+" or "-" paddle towards you and release it to shift up or down a gear. The paddles cannot select neutral or engage or disengage reverse.
Scroll the table sideways.
| Display | Meaning |
|---|---|
| P | Parking |
| R | Reverse |
| N | Neutral |
| D | Automatic forward gear |
| M1.6 | Manual forward gear (Hybrid) |
| B | Automatic forward gear with regenerative braking (Rechargeable hybrid) |
The gear engaged is shown in Manual and Sport modes, but not in all-electric driving. The gearbox status stays on the instrument panel for a few seconds after you switch off the ignition.
Electric motor (Hybrid): the motor in the gearbox is used for the first start, supplies 12 V power via the DC/DC converter and gives electric assistance to the petrol engine. It can:
It does this through the automatic functions e-Boost, e-Creeping, e-Launch, e-Queueing and e-Parking. A manual mode, e-Auto, lets you activate or deactivate the petrol engine restarting while driving. In mode P or N, the engine bay can get noisier as the traction battery starts charging: this is normal and is not a fault.
Operation: only appropriate mode changes are accepted. If you need to press the brake pedal to change mode with the engine running, an alert message appears.
Automatic functions (Hybrid): these use the electric motor for extra power or zero-emission driving. They work only if the traction battery is sufficiently charged, and all five cannot be deactivated.
Scroll the table sideways.
| Function | What it does |
|---|---|
| e-Launch | With the petrol engine off, the car drives in electric mode without affecting performance. It moves off when you press the accelerator once D or R is selected. |
| e-Creeping | With the petrol engine off, releasing the brake moves the car forwards or backwards in electric mode without the accelerator, once D or R is selected. |
| e-Queueing | Follows a queue of traffic with stops and restarts, using e-Creeping, e-Launch and electric driving. |
| e-Parking | Parking manoeuvres at reduced speed with the electric motor, with D or R selected. |
| e-Boost | Petrol engine and electric motor work together. With kick-down and a fully charged traction battery, total torque exceeds the petrol engine alone. |
Repeated use of the brake pedal restarts the petrol engine to provide braking assistance. On rechargeable hybrid versions, the gearbox picks the gear that gives optimal performance based on ambient temperature, road profile, load and driving style.
On electric versions, the drive selector is a pulse selector with a regenerative braking function. It provides traction control based on driving style, road profile and load, and with regenerative braking activated it also manages engine braking when you release the accelerator.
Scroll the table sideways.
| Mode | What it does |
|---|---|
| P (Park) | Button for parking: the front wheels are locked and the button lights up |
| R (Reverse) | Engages reverse, with your foot on the brake pedal |
| N (Neutral) | Moves the car with the ignition off so it can free-wheel (see the Free-wheeling section below) |
| D (Drive) | Automatic forward gear |
| B (Brake) | Regenerative braking: the button lights up when active |
When you switch on the ignition, the instrument panel shows P, R, N, D or B to match the selector status.
Quick change between D and R (to avoid mode N):
The driving modes available depend on your 308's engine and equipment.
The selected mode is active immediately. When the message disappears, it stays shown on the instrument panel, except for Normal mode. On an electric car, you cannot select a mode until the READY indicator lamp is displayed.
Petrol, Diesel or hybrid versions: Normal mode is selected every time you switch on the ignition.
Scroll the table sideways.
| Mode | What it does |
|---|---|
| Normal | Restores the default settings |
| Eco | Reduces energy consumption by reducing heating and air conditioning performance, without switching them off |
| Sport (manual gearbox) | More dynamic driving, acting on the power steering and accelerator, with the option to display the car's dynamic settings |
| Sport (automatic gearbox) | More dynamic driving, acting on the power steering, accelerator and gear changes, with dynamic settings display and display colour activation/deactivation (depending on version) |
Selecting Sport mode deactivates the Stop & Start function or e-Auto mode. On some Petrol or Diesel versions, in mode D with Eco or Normal mode, gently and fully releasing the accelerator lets the car free-wheel (Coasting mode) to save fuel. The drop in engine speed and noise is normal.
Rechargeable hybrid versions: Electric mode is selected every time you switch on the ignition.
Electric mode needs:
To leave Electric mode manually, fully depress the accelerator pedal or select another mode. If the car has not been used for several months, the petrol engine may restart even with a charged battery.
After several starts of the petrol engine without it warming up enough, Electric mode may be temporarily unavailable because of fuel diluting in the oil, a natural phenomenon. The message "Electric mode unavailable: automatic operation in progress" appears. To get normal electric operation back, drive approximately 50 miles (80 km) in motorway conditions or approximately 125 miles (200 km) in urban conditions. This causes no mechanical or electrical damage and can happen several times in the car's life.
Electric versions: Normal mode is selected every time you switch on the ignition. It optimises driving range and dynamic performance, and you get maximum torque and power by pressing the accelerator fully.
Stop & Start puts the engine on standby (STOP mode) when the car is stationary, for example at red lights or in traffic jams. The engine restarts automatically (START mode) as soon as you show you want to move off. It is mainly designed for town driving, to cut fuel consumption, exhaust emissions and noise when stationary, and it does not affect the car's functions, in particular the braking.
Deactivation and reactivation: the function is on by default when you switch on the ignition. You can change it in the ADAS touch screen application or through direct access to the Shortcuts for driving aids. A message on the instrument panel confirms the change. If you deactivate the function while the engine is in STOP mode, it restarts immediately.
One indicator lamp shows the function is active with the engine on standby (STOP mode), and another shows the function is deactivated or faulty.
Main conditions for operation:
Going into STOP mode:
A time counter adds up the time spent on standby during the journey and resets to zero each time you switch on the ignition.
When the engine will not go into standby: apart from when the operating conditions are not met, it will not do so:
In these cases, the indicator lamp flashes for a few seconds and then goes out.
Automatic release needs the engine running and the driver's door closed. With an automatic gearbox or drive selector, also check that the front doors are properly closed.
Avoid it where you can, but if you must, the water must not exceed 15 cm, allowing for waves. Deactivate Stop & Start and do not exceed 6 mph (10 km/h).
This can happen after several petrol engine starts without enough warm-up, because fuel dilutes in the oil. Drive approximately 50 miles (80 km) on the motorway or approximately 125 miles (200 km) in town to get normal electric operation back.
It only works if the driver's door is closed, the seat belt is fastened, the battery is charged enough, the engine is at operating temperature and it is between 0°C and 35°C outside. It also will not work on steep slopes, in Sport mode, with demisting on or when needed for cabin comfort.
Knowing how your 308 starts, parks and changes gear makes everyday driving simpler and safer. Keep this guide handy. If in doubt, ask a PEUGEOT dealer or a qualified workshop.
If a lamp comes on while you are driving, see our guides to Peugeot 308 red warning lights, Peugeot 308 orange warning lights and Peugeot 308 green and blue indicator lamps.
Don't forget to follow us on Instagram for more Peugeot guides!
This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.
Related guides: Peugeot 308 model guides.
Cover adapted from a photograph by A.BourgeoisP — Wikimedia Commons, CC BY-SA 4.0 (AI edited).
Hello and welcome. In this article we look at the fuses on the Peugeot 308 III (2021-2025). We will cover who should change a fuse and what to know before fitting extra electrical equipment or accesso
Hello and welcome. In this article we look at the fuseboxes and fuses on the Peugeot 308 II (2015-present). We will cover where the fuseboxes are, how a fuse is changed and which functions each fuse p
Hello and welcome. In this article we look at bulb replacement on the Peugeot 308 III (2021-2025). We will cover which lamps are LED, where the front and rear lamps sit, the rear foglamp and reversing