Peugeot 308Updated 19 min read

Peugeot 308 III Driver Assistance Systems

How the Peugeot 308 driver assistance systems work: speed limiter, cruise control, adaptive cruise, lane assists and Active Safety Brake.

Peugeot 308 (2021-2025) on a multi-lane motorway at sunset
Image adapted from a photo by A.BourgeoisP, CC BY-SA 4.0.

Hello and welcome. In this post, we'll look at the driver assistance systems on the Peugeot 308 III (2021-2025). Your Peugeot 308 has a range of driving and manoeuvring aids that help you control your speed, keep a safe distance, stay in your lane and avoid collisions. This guide explains how to switch on and use each system, the conditions it needs to work, and the safety points that you should keep in mind. Some systems and functions depend on the version or equipment fitted, so your 308 may not have all of them.

Can I turn off lane keeping assist on my Peugeot 308?

Only until the next time you switch on the ignition. You deactivate it in the vehicle personalisation, and it switches back on by default every time you start the engine.

Lane keeping symbols: grey paused, green active, orange fault

Quick Reference

Scroll the table sideways.

SectionIn short
Driving and manoeuvring aids - General recommendationsYour responsibilities, legal rules, radar and camera care
Speed limiterStops the car going above your set speed
Cruise controlHolds your set speed without the accelerator
Adaptive cruise controlHolds speed and keeps distance from the car ahead
Lane positioning assistSteers to keep your chosen position in the lane
Semi-automatic lane changingChanges lane for you with Drive Assist Plus 2.0
Active Safety Brake with Collision Risk Alert and Intelligent emergency braking assistanceWarns of collisions and brakes automatically
Lane keeping assistCorrects your steering if you drift from the lane

Driving and manoeuvring aids - General recommendations

Driving and manoeuvring aids can never replace your own vigilance. You must follow the Highway Code, stay in control of the car at all times and be able to take back control whenever needed. Adapt your speed to the weather, the traffic and the state of the road. These systems cannot overcome the laws of physics.

Before you use the direction indicator and change lanes, it is your job to watch the traffic, judge the distance and relative speed of other vehicles, and anticipate what they will do.

  • Driving aids: hold the steering wheel with both hands, always use the door and interior mirrors, keep your feet close to the pedals and take a break every 2 hours.
  • Manoeuvring aids: always check around the car before and during the whole manoeuvre, in particular using the mirrors.

To comply with European regulations and for safety reasons, you cannot partially or totally deactivate these functions:

  • Speed Limit Information in the Road signs recognition system.
  • Active Safety Brake/Collision Risk Alert.
  • Lane keeping assist.
  • Driver Attention Warning by Camera.
  • Parking sensors.

Radars: dirt such as mud or ice, poor weather such as heavy rain or snow, stickers or other objects over the detection zone, or damaged bumpers can affect the radars and the functions that rely on them. Do not cover the detection zones on the front and rear bumpers. If you need to repaint a bumper, contact a PEUGEOT dealer or a qualified workshop, because certain types of paint could interfere with the radars.

Driving aids camera: the camera and its functions may be impaired or stop working if the windscreen in front of it is dirty, misty, frosty, covered with snow, damaged or covered by a sticker. In humid and cold weather, demist the windscreen regularly.

Speed limiter

The speed limiter stops your 308 from going faster than the speed you have set. You switch it on manually, the minimum speed setting is 19 mph (30 km/h), and the setting stays in memory when you switch off the ignition.

Peugeot 308 III cruise-control buttons: mode selection, pause, speed adjustment and the confirm button

The steering-mounted controls are:

  • 1: speed limiter selection.
  • 2: switch on or pause the speed limiter at the previously saved speed setting.
  • 3: increase or decrease the speed setting.
  • 4: activate the speed limiter at the previously saved speed setting, or use the speed suggested by the Road signs recognition function.

The instrument panel shows the speed limiter mode, whether it is on (green) or paused (grey), the speed setting and, depending on version, the speed suggested by Road signs recognition.

To switch it on or pause it:

  1. Select the mode: press 1-LIMIT. The function is paused (grey).
  2. Switch it on: if the most recent speed setting suits you, press 2-I I> or 4-OK. The display turns green.
  3. Pause it: press 2-I I> again.

If the speed setting stays below your car's speed for a long time, you will hear an audible warning.

You do not need to switch the speed limiter on to set the speed. Make short presses up or down on 3 for steps of +/- 1 mph (1 km/h), or press and hold up or down on 3 for steps of +/- 5 mph (5 km/h).

When the function is on, you can use the speed suggested by Road signs recognition:

  • When passing the sign: press 4-OK to save the suggested speed. It immediately shows as the new speed setting.
  • After passing the sign: press 4-OK, and the message "OK?" appears. Press 4-OK again to save the suggested speed.

To go above the speed setting for a moment, fully depress the accelerator pedal. The limiter is temporarily deactivated and the speed setting flashes. Release the accelerator pedal to return below the speed setting.

Cruise control

Cruise control keeps your 308 at the speed you have set, without you using the accelerator pedal. You switch it on manually, and the car must be doing at least 25 mph (40 km/h).

  • Manual gearbox: works in whichever gear is engaged.
  • Automatic gearbox: mode D, or second gear or higher in mode M, must be engaged.
  • Drive selector: mode D or B must be engaged.

On engines with Stop & Start, cruise control stays active after changing gear, whatever the gearbox. Switching off the ignition cancels any speed setting.

The steering-mounted controls are button 1 to select cruise control, 2-I I> to switch on or pause at the saved speed, 3 to increase or decrease the speed (or to activate cruise control if it is off) and 4-OK to activate cruise control or use the speed suggested by Road signs recognition.

  1. Select the mode: press button 1. The function is paused (grey).
  2. Switch it on: once you reach the speed you want, press 3 up or down, or press 4-OK. This saves the speed setting and the display turns green.
  3. Pause it: press 2-I I>.
  4. Resume it: press 2-I I>, 3 or 4-OK again.

Cruise control also pauses:

  • when you press the brake pedal.
  • automatically, if the electronic stability control (ESC) system is triggered.
  • when you shift to neutral or engage reverse gear.
  • when you depress the clutch pedal for more than 5 seconds.
  • when you use the electric parking brake.

To change the speed setting, cruise control must be active. Make short presses up or down on 3 for steps of +/- 1 mph (1 km/h), or press and hold for steps of +/- 5 mph (5 km/h). Holding 3 for a long time changes the car's speed very quickly, so set a cruise speed fairly close to your current speed to avoid sudden acceleration or deceleration. You can also change the speed setting using the speed suggested by Road signs recognition.

Adaptive cruise control

Adaptive cruise control keeps your set speed while holding the safety distance you have chosen from the vehicle in front. It manages acceleration and deceleration for you, using a camera at the top of the windscreen and, depending on version, a radar in the front bumper.

  • Manual gearbox: the system slows the car down as far as 19 mph (30 km/h).
  • Stop & Go function: the system brakes until the car stops completely and restarts it.

The brake lamps come on when the system slows the car, and the system does not work if a brake lamp has failed. It is mainly designed for main roads and motorways, and only works with moving vehicles travelling in the same direction as you. If you use the direction indicator to overtake a slower vehicle, the system may briefly reduce the distance to the vehicle in front, without going above your speed setting.

  1. Select the system: with the engine running, press 1-ASSIST repeatedly until cruise control mode appears on the instrument panel.
  2. Wait a moment: after a few seconds the Driving aids mini-view shows in grey and cruise control is ready.
  3. Check the message: "OK?" appears when all activation conditions are met.
  4. Switch it on: press 4-OK. Your current speed becomes the speed setting (minimum 19 mph (30 km/h)) and the display turns green.

Scroll the table sideways.

GearboxSpeed range for activation
Manual gearbox19 to 112 mph (30 to 180 km/h)
Automatic gearbox or drive selector0 to 112 mph (0 to 180 km/h)

You also need the driver's door closed, the driver's seat belt fastened, second gear or higher on a manual gearbox, mode D on an automatic gearbox, the parking brake released and, if the car is stationary, the brake pedal depressed.

To change the speed setting, make short presses on 3 for steps of +/- 1 mph (1 km/h) or press and hold for steps of +/- 5 mph (5 km/h). Holding 3 for a long time changes speed rapidly. You can also save the speed suggested by Road signs recognition with 4-OK, either when passing the sign or afterwards by confirming "OK?" with a second press.

Press 2-II> or the brake pedal to pause the system. It also pauses:

  • automatically, if the ESC system is triggered.
  • when you shift to neutral or engage reverse gear.
  • below 19 mph (30 km/h) with a manual gearbox.
  • when a risk of engine stalling is detected with a manual gearbox.
  • when you depress the clutch pedal for more than 10 seconds.
  • when you use the electric parking brake.
  • when you unfasten your seat belt or open the driver's door.

Press 2-II> or 4-OK to resume. With a manual gearbox, press the accelerator to move off, then resume above 19 mph (30 km/h). With an automatic gearbox or drive selector, if the car cannot move off within 3 seconds of stopping, press 2-II> or the accelerator pedal to move off.

Lane positioning assist

Lane positioning assist identifies the edges of the lane and steers to keep your 308 in the lateral position you have chosen. It uses a camera at the top of the windscreen and suits motorways and main roads best.

The system switches on automatically when you select Drive Assist Plus mode. The instrument panel shows a steering wheel and side lines, and their colour tells you the status:

  • Grey: one or more operating conditions are not met, so the system is paused.
  • Green: all operating conditions are met and the system is active.
  • Orange: system malfunction.

To switch it off for a while, press the ASSIST button again. The Driving aids mini-view disappears. The system status is saved when you switch off the ignition.

The system needs:

  • Adaptive cruise control active.
  • ESC system operational.
  • ASR system activated.
  • No trailer detected.
  • No 'space-saver' spare wheel in use.
  • No strong lateral acceleration.
  • Direction indicators off when the system is activated.

You must hold the steering wheel properly. When the symbols are green, the system makes small steering inputs to keep your chosen position, which is not necessarily the centre of the lane, and you can feel the wheel moving. To change position, steer and hold the new position until the system takes it into account. If it is too far off-centre, the system may re-centre automatically.

If the traffic or road surface needs your intervention, act promptly and move the steering wheel to suspend the system. Pressing the brake pedal so that Adaptive cruise control pauses also pauses this system. If you are not holding the wheel firmly enough, you get a series of gradual alerts, then the system deactivates if you do not respond. In that case, press ASSIST again to reactivate it.

The system also suspends itself, with a specific audible signal, if the ESC system is triggered or if lane detection is insufficient. In the second case, Lane keeping assist can take over and the system reactivates once the conditions are met again.

Semi-automatic lane changing

With Drive Assist Plus 2.0, this system helps you change lanes. It uses the camera at the top of the windscreen, the front radar and the four angle radars in the bumpers. The steering wheel has hands-on detection to prevent distraction.

The system never replaces your vigilance. You remain responsible, so watch your surroundings and keep your hands on the wheel. If the traffic or road needs your intervention, act promptly and move the steering wheel to suspend the system. Any use of the brake or accelerator pedal that pauses or suspends adaptive cruise control also deactivates this system.

You can select it in two ways: activate Drive Assist Plus 2.0 when already on an eligible road, or, if you are using Drive Assist Plus, press OK when the car suggests it on arriving at an eligible road.

The system needs:

  • An eligible road: separate carriageways with no access for pedestrians and cyclists.
  • A lane line clear enough for the system to identify.
  • Other vehicles positioned and moving so the lane change can be made safely.
  • Drive Assist Plus 2.0 activated.
  • Lane positioning assist activated.
  • A speed between 40 and 112 mph (65 and 180 km/h).
  1. Signal: activate the direction indicator on the side you want to move to, whether or not you pass the resistance point of the stalk.
  2. Check the message: "OK?" appears if the conditions are met.
  3. Confirm: after checking your surroundings, press 2-OK. "Stay attentive" appears as a reminder that you are still responsible.
  4. Let the system steer: it moves the car into the target lane with small steering actions, and you can feel the wheel moving.
  5. Return the stalk: if you pushed the indicator beyond the resistance point, pull it back.

Once the manoeuvre is done, the system deactivates and lane positioning assist takes over. You can take back control at any time by cancelling the indicator before the car crosses the line, holding the wheel firmly or using the pedals.

Active Safety Brake with Collision Risk Alert and Intelligent emergency braking assistance

This system warns you if there is a risk of collision with the vehicle ahead, a pedestrian or a cyclist, and reduces your speed to avoid the collision or limit its severity. It also takes motorcyclists into account and may react to animals, but animals (especially those smaller than 0.5 m) and objects on the road are not necessarily detected.

It includes three functions: Collision Risk Alert, Intelligent emergency braking assistance (iEBA) and Active Safety Brake (automatic emergency braking). It uses a multifunction camera at the top of the windscreen and, depending on version, a radar in the front bumper. When it detects a possible collision, it prepares the braking circuit, which may cause a slight noise and a slight feeling of deceleration. The system does not replace your vigilance.

It needs the brake system operational, ASR activated, all seat belts fastened and a steady speed on roads with little or no curvature. If its warning lamp comes on without a message, automatic braking is not available because a condition is not met. This is normal and does not need a workshop.

With the ignition on, deactivate the system in the driving aids touch screen application whenever automatic braking could be a risk, for example:

  • Carrying long objects on roof bars.
  • Using an automatic car wash.
  • Doing maintenance, such as changing a wheel or working in the engine compartment.
  • Placing the car on a rolling bench in a workshop.
  • Towing the car.
  • After damage to the windscreen near the camera.

The system switches itself off if it detects a spare wheel with too small a diameter, a fault with the brake pedal switch or a brake lamp, a fault in the sensors, electronics or brake system, a trailer on the equipped tow hitch, or a severe crash such as one with airbag deployment.

Performance may be reduced by snow, ice, mud or dirt on the sensor, a dirty or damaged windscreen, a damaged front bumper, stickers, a misplaced camera, bends, bad weather, spray, sun glare, poor or changing light, banked or hilly roads and vehicle modifications such as tyres. When detection is reduced by the environment, no message is shown. Driving with faulty brake lamps can be dangerous, and you must not overload the car beyond the GVW, GTW and roof bar load height limits.

You can set how early Collision Risk Alert warns you in the ADAS touch screen application, under Functions>Automatic Braking System. Choose "Far", "Medium" or "Near". The setting is saved when you switch off the ignition.

Scroll the table sideways.

Alert levelWhat you getMeaning
Level 1Visual alert, "Vehicle close"The vehicle ahead is very close
Level 2Visual and audible alert, "Brake!"A collision is imminent
Level 3Micro-braking (optional)Confirms the risk of collision

If you approach a vehicle too quickly, level 2 may appear straight away. Level 1 depends on the threshold you chose, reacts only to moving vehicles and switches off automatically at lower speed.

Lane keeping assist

Lane keeping assist corrects your 308's trajectory if it detects a risk of drifting out of the lane unintentionally or, depending on version, crossing a verge or hard shoulder. It uses a camera at the top of the windscreen and is most useful on motorways and main roads.

Because of legal requirements, you can only deactivate it in the vehicle personalisation until the next time you switch on the ignition. It switches on by default every time you start the engine. If a correction lasts more than 10 s, you get a message and an audible signal, and if you still cannot keep the car in the lane, the correction stops after a short time.

The system needs:

  • A speed between 40 and 112 mph (65 and 180 km/h).
  • A road marked with a central dividing line.
  • The steering wheel held with both hands.
  • Direction indicators off when the system is activated.
  • The ESC system activated and operational.

The system only helps if the car risks wandering from its lane. It does not manage distance, speed or braking. Keep both hands on the wheel so you stay in control if the system can no longer work, for example if the central line disappears.

When it detects a risk of crossing a lane marking or a lane boundary such as a grass verge, it steers the car back into its lane. You will feel the wheel turn and the warning lamp flashes. You can stop the correction by holding the wheel firmly, for example in an emergency manoeuvre, and it stops immediately if you use the direction indicators. While the indicators are on, and for a few seconds after, no correction is made.

If the system decides a correction will not be enough and a solid line will be crossed, you will see "Hold the steering wheel" or "Stay in lane" (depending on version). If you are not holding the wheel properly, an audible warning sounds until the correction ends or you grip the wheel. Repeated corrections make the warnings longer, until they become continuous.

The system goes into standby automatically if:

  • ESC is deactivated or triggered.
  • Speed is below 40 mph (65 km/h) or above 112 mph (180 km/h).
  • A trailer is electrically connected.
  • A "space-saver" spare wheel is detected. Detection is not immediate, so deactivating the system is recommended.
  • A dynamic driving style or pressure on the brake or accelerator pedal is detected.
  • You drive over lane markings or use the direction indicators.
  • You cross the inside line on a bend or drive on a tight bend.
  • You drive on hilly roads.
  • Driver inactivity is detected during a correction.
  • A narrow lane is detected.

The system may also be disturbed or stop working when Lane positioning assist is active, in poor visibility such as heavy rain, thick fog or snowfall, or when dazzled by oncoming headlamps, low sun, reflections or leaving a tunnel.

Frequently Asked Questions

Can I turn off lane keeping assist on my Peugeot 308?

Only until the next time you switch on the ignition. You deactivate it in the vehicle personalisation, and it switches back on by default every time you start the engine.

What is the minimum speed for cruise control on a Peugeot 308?

Standard cruise control needs at least 25 mph (40 km/h). With adaptive cruise control and a manual gearbox, your speed must be between 19 and 112 mph (30 and 180 km/h).

Why has my Peugeot 308 cruise control paused by itself?

Cruise control pauses if you press the brake, shift to neutral or reverse, hold the clutch down too long, use the electric parking brake or if ESC is triggered. Adaptive cruise control also pauses if you unfasten your seat belt or open the driver's door.

How do I change the collision warning sensitivity on my Peugeot 308?

In the ADAS touch screen application, select Functions>Automatic Braking System and choose "Far", "Medium" or "Near". The setting is saved when you switch off the ignition.

The driver assistance systems on your Peugeot 308 can make long journeys easier, but you are always the one in charge. Keep the windscreen and bumpers clean, keep your hands on the wheel, and for full details on any system, ask a PEUGEOT dealer or a qualified workshop.

More Peugeot 308 Guides

If a driving aid lamp lights up on your dashboard, see our guides to Peugeot 308 orange warning lights, Peugeot 308 green and blue indicator lamps and Peugeot 308 red warning lights.

Don't forget to follow us on Instagram for more Peugeot guides!

This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.

Related guides: Peugeot 308 model guides.

Cover adapted from a photograph by A.BourgeoisP — Wikimedia Commons, CC BY-SA 4.0 (AI edited).

Related guides

Guide ·

Peugeot 308 Fuse Box and Fuses (2021-2025)

Hello and welcome. In this article we look at the fuses on the Peugeot 308 III (2021-2025). We will cover who should change a fuse and what to know before fitting extra electrical equipment or accesso

Guide ·

Peugeot 308 Fuse Box and Fuses (2015-present)

Hello and welcome. In this article we look at the fuseboxes and fuses on the Peugeot 308 II (2015-present). We will cover where the fuseboxes are, how a fuse is changed and which functions each fuse p

Guide ·

Peugeot 308 Bulb Replacement (2021-2025)

Hello and welcome. In this article we look at bulb replacement on the Peugeot 308 III (2021-2025). We will cover which lamps are LED, where the front and rear lamps sit, the rear foglamp and reversing