Peugeot 308Updated 23 min read

Peugeot 308 III Hybrid and e-308 Charging

How to charge your Peugeot 308 rechargeable hybrid or electric: modes 2, 3 and 4, deferred charging, indicator lamps. Covers the Peugeot 308 III.

Peugeot 308 (2021-2025) plugged into a public charging station
Image adapted from a photo by A.BourgeoisP, CC BY-SA 4.0.

Hello and welcome. In this post, we'll look at how to charge the plug-in hybrid 308 and the e-308, including the charge flap and cable types on the Peugeot 308 III (2021-2025). It covers the safety recommendations, the mode 2 control unit on the domestic charging cable, deferred charging, the indicator lamps in the charging flap and the step-by-step charging procedures for each mode. This guide covers the Peugeot 308 III (2021-2025), including vehicles produced from 07/08/2023. Some functions, cables and charging modes depend on the version or equipment fitted, so not everything here will apply to your car.

How do you charge a Peugeot 308 Hybrid or e-308?

Unlock and open the charge flap, fit the matching cable until it locks, then follow the lamp colours on the flap to see when charging has started and when it has finished.

Quick Reference

Scroll the table sideways.

SectionIn short
Rechargeable hybrid or electric vehicles - Specific recommendationsSafety, battery care and the mode 2 control unit
Charging the traction battery (Rechargeable hybrid)How to charge the rechargeable hybrid at home or Wallbox
Charging system (Electric)Charging connectors, lamps, cables and modes on electric versions
Charging the traction battery (Electric)Charging the electric version in modes 2, 3 and 4

Rechargeable hybrid or electric vehicles - Specific recommendations

These recommendations apply only to rechargeable hybrid and electric versions. They also introduce the control unit (mode 2) that you need for standard charging at home.

Peugeot 308 III charge flap on the rear wing, with the charging inlet behind it

Safety labels: the high-voltage label on the car is intended only for firefighters and maintenance services if work is carried out on the vehicle. No other person must touch the device shown on this label.

After an accident or an impact to the underbody: the electrical circuit or the traction battery can be seriously damaged. Stop as soon as it is safe to do so, switch off the ignition and contact a PEUGEOT dealer or a qualified workshop.

Water and wet hands: never let water or dust get into the connector or the charging nozzle, as there is a risk of electrocution or fire. Never connect or disconnect the charging nozzle or cable with wet hands, as there is a risk of electrocution.

Washing:

  • Before washing the car, always check that the charging flap is closed correctly.
  • Never wash the car while the battery is on charge.
  • High-pressure washing in the engine compartment or under the body is expressly prohibited, to avoid damaging the electrical components.
  • Do not use a pressure greater than 80 bar when washing the bodywork.

Looking after the traction battery: to preserve your car's mileage and the durability of the traction battery, PEUGEOT recommends that you:

  • Do not fully charge the battery of your electric vehicle every day. Charge the traction battery below 80% as often as possible.
  • Do not completely discharge the battery.
  • Do not leave the car unused for a long period (more than 12 hours) when the traction battery has a low or high charge level. A charge level between 20 and 40% is preferable.
  • Limit your use of fast charging.
  • Do not expose the car to temperatures below -30°C or above +60°C for more than 24 hours.
  • Avoid charging at negative temperatures (unless the car has been driven for more than 20 minutes) or above +30°C.
  • Do not use the traction battery as a generator of energy.
  • Do not use a generator to recharge the traction battery.

Electromagnetic fields: rechargeable hybrid and electric vehicles have been developed in line with the maximum electromagnetic field limits recommended by the ICNIRP (International Commission on Non-Ionizing Radiation Protection - 1998 Guidelines).

Pacemakers and similar devices: if you wear a pacemaker or a similar device, ask your doctor or the device manufacturer which precautions or instructions you should follow. Make sure the device is guaranteed to work in an environment that meets the ICNIRP recommendations. If you are in any doubt:

  • Domestic or accelerated charging (mode 2 or 3): do not stay inside or near the car, the charging cable or the charging unit, even for a short time.
  • Superfast charging (mode 4, Electric): do not use the system yourself and avoid going near public fast charging points. Leave the area and ask someone else to recharge the car.

Control unit (mode 2) indicator lamps:

  • POWER: green means the electrical connection is established and charging can begin.
  • CHARGE: flashing green means charging is in progress or temperature pre-conditioning is activated. Fixed green means charging is complete.
  • FAULT: red means there is a fault and charging is not permitted or must be stopped immediately. Check that everything is connected correctly and that the electrical system is not faulty. If the lamp does not go off, contact a PEUGEOT dealer or a qualified workshop.

When you plug the charging cable into a domestic socket, all of the indicator lamps come on briefly. If none of them come on, check the domestic socket's circuit-breaker:

  • If the circuit-breaker has tripped, ask a professional to check that the electrical system is compatible and to carry out any repairs needed.
  • If the circuit-breaker has not tripped, stop using the charging cable and contact a PEUGEOT dealer or a qualified workshop.

Control unit label recommendations: the label sets out these rules:

  • Incorrect use of the charging cable can result in fire, property damage and serious injury or death by electrocution.
  • Always use a correctly earthed power socket protected by a 30 mA residual current device.
  • Always use a socket protected by a circuit-breaker suited to the current rating of the electrical circuit.
  • The weight of the control unit must not hang on the socket, plug or cables.
  • Never use the charging cable if it is defective or damaged in any way.
  • Never try to repair or open the charging cable. It has no repairable parts, so replace it if it is damaged.
  • Never immerse the charging cable in water.
  • Never use the cable with an extension cable, a multi-plug socket, a conversion adaptor or a damaged socket.
  • Do not pull the plug out of the wall as a way of stopping charging.
  • If the charging cable or wall socket feels burning hot, stop charging immediately by locking and then unlocking the car with the remote control key.
  • The cable contains components that can cause electrical arcing or sparks. Do not expose it to flammable vapours.
  • Only use this charging cable with PEUGEOT vehicles.
  • Never plug the cable into the wall socket, or unplug it, with wet hands.
  • Do not force the connector if it is locked into the car.

Control unit lamp states:

Scroll the table sideways.

Lamps litMeaning
NoneNot connected to the power supply, or no power available from the infrastructure.
POWER (green), CHARGE (green) and FAULT (red)The control unit is performing a self-test, or it is in diagnostic mode.
POWER (green) onlyConnected only to the infrastructure, or to the infrastructure and the car, but no charging in progress.
POWER (green) and CHARGE (green)Connected to the power supply and the car. The car is on charge or in a temperature pre-conditioning sequence, or it is waiting to charge or has finished charging.
FAULT (red) onlyControl unit malfunction. No charging allowed.

If an error indicator comes back after a manual reset, the control unit must be checked by a PEUGEOT dealer before the next charge. To reset the control unit manually:

  1. Disconnect: unplug the charging connector and the wall socket at the same time.
  2. Reconnect: plug into the wall socket first.

Charging the traction battery (Rechargeable hybrid)

For a full charge on the rechargeable hybrid, follow the charging procedure without interrupting it until it stops automatically. Charging can start immediately (the default) or be deferred, which you set on the touch screen or in the MYPEUGEOT APP application.

While the car is connected, the instrument panel shows:

  • Traction battery charge status (%).
  • Remaining range (miles or km).
  • Estimated charging time (the calculation can take a few seconds).
  • Charging speed (miles or km gained per hour).

After the instrument panel goes into standby, you can display this information again by unlocking the car or opening a door. You can also follow the charging progress in the MYPEUGEOT APP application. In Lounge mode, with the car connected, you can switch on the ignition and use certain functions, such as the audio and telematics system and the air conditioning, for several hours.

Low charge level: driving with too little charge in the traction battery can lead to a breakdown, accidents or serious injuries, so always make sure it has enough charge. If the outside temperature is negative, avoid parking outside for several hours with a low charge (less than 20%).

Storing the car for more than 1 month: if the car is not used for more than 4 weeks and cannot be charged when you restart it, self-discharge can make it impossible to restart if the charge level is low or very low, especially at negative temperatures. If you will not use the car for several weeks:

  • Make sure the traction battery has a charge between 20% and 40%.
  • Do not connect the charging cable.
  • Always park in a place with temperatures between -10°C and 30°C, as extreme temperatures can damage the traction battery.
  • Ask a PEUGEOT dealer or a qualified workshop if you need the battery disconnection procedure.

Before charging: depending on your situation, have a professional check that the electrical system complies with the applicable standards and is compatible with the car, and have a professional electrician install a dedicated domestic power socket or accelerated charging unit (Wallbox) that is compatible with the car. Use the charging cable supplied with the car.

During charging:

  • As a safety measure, the engine will not start while the charging cable is plugged into the car's connector. A warning appears on the instrument panel.
  • Unlocking the car while it is charging stops the charging. If you do not open a door or the boot, or touch the charging nozzle, the car locks again after 30 seconds and charging resumes automatically.
  • Never work under the bonnet. Some areas stay very hot even an hour after charging ends (risk of burns), and the fan can start at any time (risk of cuts or strangulation).

After charging: check that the charging flap is closed. Do not leave the cable connected to the domestic socket, as there is a risk of short-circuit or electrocution if it comes into contact with water or is immersed.

Deferred charging: by default, the start time is set to around midnight. Depending on equipment, you can change it:

  1. Open the settings: in the Energy touch screen application, select the Charging tab.
  2. Set the time: choose the charging start time.
  3. Confirm: press OK. The setting is saved in the system.

You can also programme deferred charging from a smartphone with the MYPEUGEOT APP application. To activate it:

  1. Connect: after programming, connect the car to the charging equipment.
  2. Activate: press the button in the charging flap within one minute. The light guides come on in blue to confirm.

Connection:

  1. Check the car: make sure the gear selector is in mode P and the ignition is off, otherwise charging is impossible.
  2. Open the flap: press on the rear of the charging flap and check there are no foreign bodies on the charging connector. The light guides in the flap come on white.

Domestic charging (mode 2):

  1. Plug in at the wall: connect the control unit's charging cable to the domestic socket. All the lamps on the control unit light up, then only POWER stays on in green.
  2. Remove the cover: take the protective cover off the charging nozzle.
  3. Insert the nozzle: push it into the car's charging connector.

The green light guides in the flap and the green CHARGE lamp on the control unit flash to confirm that charging has started. If they do not, restart the procedure and make sure every connection is properly made. The red lamp in the flap comes on to show the nozzle is locked.

Accelerated charging (mode 3):

  1. Prepare the Wallbox: follow the charging unit's user instructions.
  2. Remove the cover: take the protective cover off the charging nozzle.
  3. Insert the nozzle: push it into the car's charging connector.

The green light guides in the flap flash to confirm that charging has started. If they do not, restart the procedure and make sure every connection is properly made. The red lamp in the flap comes on to show the nozzle is locked.

Disconnection:

  1. Release the nozzle: if the car is locked, unlock it. If it is unlocked, lock it and then unlock it. With selective door unlocking activated, press the unlocking button on the remote control twice. The red lamp in the flap goes out to confirm the nozzle is unlocked.
  2. Remove the nozzle: take it out within 30 seconds.

In mode 2, the end of charging is confirmed when the green CHARGE lamp on the control unit and the green light guides in the flap come on fixed. After disconnecting, put the protective cover back on the nozzle, close the charging flap and unplug the control unit's cable from the domestic socket.

In mode 3, the end of charging is confirmed by the Wallbox and by the green light guides in the flap coming on fixed. After disconnecting, put the nozzle back on the charging unit and close the charging flap.

Charging system (Electric)

The electric drive system runs at approximately 400 V. You can recognise it by its orange cables, and its components carry a specific warning symbol. The power train can become hot during use and after you switch off the ignition, so follow the warning messages on the labels, especially those inside the charging flap.

Traction battery: this battery stores the energy that powers the electric motor and the thermal comfort equipment in the passenger compartment. It discharges as you drive and must be recharged regularly. You do not need to wait for it to reach its reserve level before recharging. Its range varies with your type of driving, your route, your use of thermal comfort equipment and the ageing of its components. Its lifespan depends on factors such as climate, distance travelled and how often it has been fast-charged.

Inside the charging flap:

  • Charging connectors.
  • Deferred charging activation button.
  • Nozzle locking indicator lamp: fixed red means the nozzle is positioned correctly and locked in the connector. Flashing red means the nozzle is incorrectly positioned or cannot be locked.
  • Charging indicator lamp: see the table below.

Scroll the table sideways.

Charging indicator lampMeaning
Fixed whiteWelcome lighting when you open the flap and disconnect the charging cable.
Flashing whiteCharging initialisation.
Fixed blueDeferred charging.
Flashing greenCharging in progress.
Fixed greenCharging complete. The lamp goes off after about 2 minutes as the car's functions go into standby. It comes on again to show the battery is fully charged when you unlock the car with the Keyless Entry and Start system or open a door.
Fixed redMalfunction.

If the charging flap takes an impact, even a light one, do not use it. Never dismantle or modify the charging connector, as there is a risk of electrocution and fire. Contact a PEUGEOT dealer or a qualified workshop.

Charging cables: the cable supplied with the car (depending on version) is compatible with the electrical systems in the country of sale. When you travel abroad, check that the local electrical systems are compatible with it. A full range of charging cables is available from your dealer, so contact a PEUGEOT dealer or a qualified workshop for more information and suitable cables.

Identification labels: labels on the car, the charging cable and the charger tell you which device to use.

Scroll the table sideways.

LocationConfigurationPower type/Voltage range
Charging connector (vehicle side)TYPE 2AC < 480 Vrms
Charging socket (charger side)TYPE 2AC < 480 Vrms
Charging connector (vehicle side)COMBO 2 (FF)DC 50 V - 500 V

Charging modes:

  • Standard charging, mode 2 (AC, domestic socket): 8 A maximum charging current with a standard socket, 16 A maximum with a Green'Up socket. Call a professional installer to fit this type of socket. The specific domestic charging cable carries identification label C on the vehicle-side connector.
  • Accelerated charging, mode 3 (single-phase or three-phase AC, depending on version): 32 A maximum charging current with an accelerated charging unit (Wallbox). The mode 3 cable carries identification label C on the vehicle-side connector and on the charger-side socket.
  • Superfast charging, mode 4 (DC, fast public charger): the cable is integrated into the fast public charger and has identification label K on the vehicle-side connector. Only use fast public chargers where the cable length does not exceed 30 metres.

You must not damage the mode 2 cable. If it is damaged, do not use it and contact a PEUGEOT dealer or a qualified workshop to replace it. Never dismantle or modify an accelerated charging unit (risk of electrocution and fire), and follow its manufacturer's user manual for operating instructions.

Charging the traction battery (Electric)

To recharge the electric 308, connect it to a domestic electricity supply (domestic or accelerated charging) or to a fast public charger (superfast charging). For a full charge, follow the procedure without pausing until it ends automatically. Charging can be immediate or deferred, except on a fast public charger (mode 4).

You can stop domestic or accelerated charging at any time by unlocking the car and removing the nozzle. For superfast charging, follow the fast public charger's instructions. You can also follow charging progress in the MYPEUGEOT APP application.

  • As a safety measure, the car will not start while the charging cable is plugged into its connector. A warning appears on the instrument panel.
  • The cooling fan in the engine compartment comes on during charging to cool the on-board charger and the traction battery.

Low charge level: driving with too little charge in the traction battery can lead to a breakdown, accidents or serious injuries, so always make sure it has enough charge. If the outside temperature is negative, avoid parking outside for several hours with a low charge (less than 20%).

Storing the car for more than 1 month: if the car is not used for more than 4 weeks and cannot be charged when you restart it, self-discharge can make it impossible to restart if the charge level is low or very low, especially at negative temperatures. If you will not use the car for several weeks:

  • Make sure the traction battery has a charge between 20% and 40%.
  • Do not connect the charging cable.
  • Always park in a place with temperatures between -10°C and 30°C, as extreme temperatures can damage the traction battery.
  • Disconnect the cable from the (+) terminal of the accessory battery in the engine compartment.
  • About every 3 months, connect a 12 V battery charger to the (+) and (-) terminals of the accessory battery to recharge it and keep an operating voltage.
  • Ask a PEUGEOT dealer or a qualified workshop if you need the battery disconnection procedure.

Before domestic or accelerated charging: depending on your situation, have a professional check that the electrical system complies with the applicable standards and is compatible with the car, and have a professional electrician install a dedicated domestic power socket or accelerated charging unit (Wallbox) that is compatible with the car. Use the charging cable available as an accessory.

During domestic or accelerated charging:

  • Unlocking the car stops the charging. If you do not open a door or the boot, or touch the charging nozzle, the car locks again after 30 seconds and charging resumes automatically.
  • Never work under the bonnet. Some areas stay very hot even an hour after charging ends (risk of burns), and the fan can start at any time (risk of cuts or strangulation).

After domestic or accelerated charging: check that the charging flap is closed. Do not leave the cable connected to the domestic socket, as there is a risk of short-circuit or electrocution if it comes into contact with water or is immersed.

Superfast charging: before charging, check that the fast public charging station and its cable are compatible with the car. Below 0°C, charging times can be longer. Below -20°C, charging is still possible but takes even longer, because the battery has to be heated first. After charging, check that the charging flap is closed.

Deferred charging: this is only possible in modes 2 and 3. By default, the start time is set to around midnight. Depending on equipment, you can change it:

  1. Open the settings: in the Energy touch screen application, select the Charging tab.
  2. Set the time: choose the charging start time.
  3. Confirm: press OK. The setting is saved in the system.

You can also programme deferred charging from a smartphone with the MYPEUGEOT APP application. To activate it:

  1. Connect: after programming, connect the car to the charging equipment.
  2. Lock: lock the car.
  3. Activate: press the button in the charging flap within one minute. The charging indicator lamp comes on in blue to confirm.

Connection:

  1. Check the selector: make sure the drive selector is in mode P, otherwise charging is not possible.
  2. Open the flap: press the push-button to open the charging flap and check there are no foreign bodies on the charging connector.

Domestic charging, mode 2:

  1. Plug in at the wall: connect the control unit's charging cable to the domestic socket. All the lamps on the control unit light up, then only POWER stays on in green.
  2. Remove the cover: take the protective cover off the charging nozzle.
  3. Insert the nozzle: push it into the charging connector.

The green CHARGE lamps flash, first in the flap and then on the control unit, to confirm that charging has started. If they do not, restart the procedure and make sure every connection is properly made. The red lamp in the flap comes on to show the nozzle is locked. Once charging is complete, if the cable is still connected, opening the driver's door shows the charge level on the instrument panel for about 20 seconds.

Accelerated charging, mode 3:

  1. Prepare the Wallbox: follow the charging unit's user instructions.
  2. Remove the cover: take the protective cover off the charging nozzle.
  3. Insert the nozzle: push it into the charging connector.

The charging indicator lamp in the flap flashes green to confirm that charging has started. If it does not, restart the procedure and make sure the connection is properly made. The red lamp in the flap comes on to show the nozzle is locked.

Superfast charging, mode 4:

  1. Remove the lower cover: depending on version, take the protective cover off the lower part of the connector.
  2. Connect the charger: follow the fast public charger's instructions and connect its cable to the car's connector.

The charging indicator lamp in the flap flashes green to confirm that charging has started. If it does not, restart the procedure and make sure the connection is properly made. The red lamp in the flap comes on to show the nozzle is locked. In mode 4 only, you can also pause charging by pressing the button in the flap.

Disconnection:

  1. Release the nozzle: if the car is unlocked, lock it and then unlock it. If it is locked, unlock it. With selective door unlocking activated, press the unlocking button twice. The red lamp in the flap goes out to confirm the nozzle is unlocked.
  2. Remove the nozzle: in modes 2 and 3, take it out within 30 seconds. The charging indicator lamp comes on in white.

When charging is complete, the green charging indicator lamp in the flap goes out after about 2 minutes.

Finishing in mode 2: the end of charging is confirmed when the green CHARGE lamp on the control unit and the green charging lamp in the flap come on fixed. Put the protective cover back on the nozzle, close the charging flap and unplug the control unit end of the cable from the domestic socket.

Finishing in mode 3: the charging control unit shows the end of charging and the green lamp in the flap comes on fixed. Hang the nozzle back on the charging unit and close the charging flap.

Finishing in mode 4: the charger shows the end of charging and the green lamp in the flap comes on fixed. Hang the nozzle back on the charger, replace the protective cover on the lower section (depending on version) and close the charging flap.

When you disconnect the nozzle, a message on the instrument panel says charging is complete, even if you disconnected it before the battery was fully charged.

Frequently Asked Questions

Why won't my Peugeot 308 start while it is plugged in?

As a safety measure, the car will not start while the charging cable is plugged into its connector, and a warning appears on the instrument panel. Disconnect the charging nozzle first.

How do I stop charging my electric Peugeot 308?

On the electric version, you can stop domestic or accelerated charging (modes 2 and 3) at any time by unlocking the car and removing the nozzle. For superfast charging (mode 4), follow the fast public charger's instructions, or press the button in the flap to pause charging.

Do not pull the plug out of the wall to stop charging.

How do I unlock the charging cable from my Peugeot 308?

If the car is locked, unlock it. If the car is already unlocked, lock it and then unlock it. The red lamp in the flap goes out when the nozzle is released. On the rechargeable hybrid, and on the electric version in modes 2 and 3, you must then remove the nozzle within 30 seconds.

Charge-flap lamp colours and the cable types used for domestic, accelerated and rapid charging

What charge should I leave in my 308 battery if I'm not using it for weeks?

make sure the traction battery has a charge between 20% and 40%, not to connect the charging cable, and to park somewhere between -10°C and 30°C.

Charging your Peugeot 308 is simple once you know which mode you are using and what the lamps in the flap and on the control unit are telling you. Follow the safety advice in this guide, and if anything looks wrong with the cable, the flap or a lamp, contact a PEUGEOT dealer or a qualified workshop.

More Peugeot 308 Guides

If a lamp comes on while you are driving, see our guides to the Peugeot 308 red warning lights, the Peugeot 308 orange warning lights and the Peugeot 308 green and blue indicator lamps.

Don't forget to follow us on Instagram for more Peugeot guides!

This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.

Related guides: Peugeot 308 model guides.

Cover adapted from a photograph by A.BourgeoisP — Wikimedia Commons, CC BY-SA 4.0 (AI edited).

Related guides

Guide ·

Peugeot 308 Fuse Box and Fuses (2021-2025)

Hello and welcome. In this article we look at the fuses on the Peugeot 308 III (2021-2025). We will cover who should change a fuse and what to know before fitting extra electrical equipment or accesso

Guide ·

Peugeot 308 Fuse Box and Fuses (2015-present)

Hello and welcome. In this article we look at the fuseboxes and fuses on the Peugeot 308 II (2015-present). We will cover where the fuseboxes are, how a fuse is changed and which functions each fuse p

Guide ·

Peugeot 308 Bulb Replacement (2021-2025)

Hello and welcome. In this article we look at bulb replacement on the Peugeot 308 III (2021-2025). We will cover which lamps are LED, where the front and rear lamps sit, the rear foglamp and reversing