Peugeot 3008 I Indicators: Green and Blue Warnings (2016-present)

Green and blue lamps on your instrument panel are operation indicator lamps. When one comes on, it confirms that the matching system or function has been switched on. They are not fault warnings, but they tell you what the car is doing.

This guide covers the Peugeot 3008 I (2016-present) and is based on handbook edition ed01-16, which applies to vehicles produced from 01/09/2016. Some of these lamps only appear on certain versions or with certain equipment, so your car may not show all of them.

Quick Reference

Left-hand direction indicator

This lamp flashes with a buzzer when you push the lighting stalk down. It confirms that your left-hand direction indicator is on.

What to do:

• No action is needed. The lamp simply confirms you are signalling left.

Right-hand direction indicator

This lamp flashes with a buzzer when you push the lighting stalk up. It confirms that your right-hand direction indicator is on.

What to do:

• No action is needed. The lamp simply confirms you are signalling right.

Hazard warning lamps

This lamp flashes with an audible signal when the hazard warning lamps switch on the dashboard has been pressed. It confirms your hazard warning lamps are on.

What to do:

• Expect the left-hand and right-hand direction indicators, and their indicator lamps on the instrument panel, to flash at the same time.

Sidelamps

This lamp stays on steadily when the lighting stalk is set to the sidelamps position. It confirms your sidelamps are switched on.

What to do:

• No action is needed. The lamp simply confirms your sidelamps are on.

Dipped beam headlamps

This lamp stays on steadily when the lighting stalk is set to the dipped beam headlamps position. It confirms your dipped beam is switched on.

What to do:

• No action is needed. The lamp simply confirms your dipped beam headlamps are on.

Main beam headlamps

This lamp stays on steadily when you have pulled the lighting stalk towards you. It confirms your main beam headlamps are on.

What to do:

• Pull the lighting stalk when you want to switch back to dipped beam headlamps.

Automatic headlamp dipping or

One of these lamps stays on steadily when Automatic headlamp dipping has been switched on in the Driving menu of the touch screen and the lighting stalk is in the AUTO position. It confirms the function is active.

What to do:

• Let the system work: the camera at the top of the windscreen switches between main beam and dipped beam to suit the outside light and driving conditions.
• See the Automatic headlamp dipping section of your handbook for full details.

Front foglamps

This lamp stays on steadily when the front foglamps have been switched on with the ring on the lighting stalk. It confirms they are on.

What to do:

• To switch the front foglamps off, turn the ring on the lighting stalk backwards twice.

Stop & Start

This lamp can stay on steadily or flash briefly. When it is steady, the Stop & Start system has put the engine into STOP mode because the car has stopped, for example at red lights or in a traffic jam. When it flashes for a few seconds and then goes off, STOP mode is temporarily unavailable, or START mode has been triggered automatically.

What to do:

If the lamp is steady:

• Simply move off when you are ready. The lamp goes off and the engine restarts automatically in START mode.

If the lamp flashes briefly, then goes off:

• See the Stop & Start section of your handbook for more information.

Hill Assist Descent Control

This lamp can stay on steadily or flash. When it is steady, the system is switched on but the conditions it needs to control your speed are not met, such as the gradient or the gear engaged. When it flashes, the system is actively controlling the speed of the car.

What to do:

If the lamp is steady:

• The system is on but not yet controlling your speed.

If the lamp is flashing:

• Expect the car to brake itself, with the brake lamps lighting up during the descent.
• See the Hill Assist Descent Control section of your handbook for more information.

Blind Spot Monitoring System

This lamp stays on steadily when the Blind Spot Monitoring System has been switched on. It confirms the system is active.

What to do:

• See the Blind Spot Monitoring System section of your handbook for more information.

Automatic wiping

This lamp stays on steadily when you have pushed the wiper stalk down. It confirms that automatic front wiping is switched on.

What to do:

• To switch automatic wiping off, push the wiper stalk down again or move it to another position.

If You're Not Sure

If a lamp comes on and you are not sure why, read the message shown on the instrument panel alongside it, then check the matching section of your handbook. If you still have a problem, contact a PEUGEOT dealer or a qualified workshop.

Green and blue lamps are there to confirm what your Peugeot 3008 is doing, so in most cases you just need to know which system is on. Keep this guide handy and you will always know what you are looking at.

Related guides: Peugeot 3008 I (2016-present) red warning lights, Peugeot 3008 I (2016-present) orange warning lights, Peugeot 3008 Warning Lamps: Blue and Green Warnings (general guide) and all Peugeot 3008 guides.