Peugeot 208Updated 13 min read

Peugeot 208 I Flat Tyre and Repair Kit

How to use the temporary puncture repair kit, check tyre pressures and change a wheel on your Peugeot 208 I. Covers the Peugeot 208 I (2015-present).

Peugeot 208 (2015-present) in a mountain lay-by with the boot open
Image adapted from a photo by Harvey Bold, CC0.

Hello and welcome. In this post, we'll look at the temporary puncture repair kit and the spare wheel on the Peugeot 208 I (2015-present). A flat tyre is never welcome, but your Peugeot 208 gives you two ways to deal with it. Depending on the car, you have either a temporary puncture repair kit or a spare wheel with a set of tools. This guide explains how to use the kit, how to check and adjust your tyre pressures with the compressor, and how to change a wheel safely. Some items depend on the version, country or equipment fitted, so not everything here will apply to your 208.

Where is the puncture repair kit on a Peugeot 208?

The kit is in the under-floor storage, under the boot floor. It contains a 12 V compressor with a pressure gauge, a sealant cartridge with a hose and a speed-limit sticker.

Quick Reference

Scroll the table sideways.

SectionIn short
Temporary puncture repair kitWhat the kit does and what it contains
Repair procedureStep-by-step puncture repair with sealant and compressor
Checking / adjusting tyre pressuresUsing the compressor alone to check tyre pressures
Access to the toolsWhere the wheel-changing tools are stored
List of toolsThe tools supplied and what each is for
Access to the spare wheelTaking out and refitting the spare wheel
Removing a wheelParking safely, jacking up and removing the wheel
Fitting the wheelFitting the spare and speed limits afterwards

Temporary puncture repair kit

The temporary puncture repair kit is made up of a compressor and a sealant cartridge. It lets you repair a tyre temporarily so that you can drive to the nearest garage. It is designed to repair most punctures on the tyre tread or shoulder.

Peugeot 208 I tyre repair kit: compressor, hose and sealant bottle

The kit is stored in the under floor storage, under the boot floor. It contains:

  • 12 V compressor: with an integral pressure gauge.
  • Sealant cartridge: with an integral hose.
  • Speed limit sticker: to remind you that a tyre is in temporary use.

Your car's electrical system lets you run the compressor for long enough to inflate a tyre after a puncture repair.

Repair procedure

Follow these steps in order to repair a punctured tyre with the kit.

  1. Park safely: stop the car where it does not obstruct traffic and apply the parking brake.
  2. Follow the safety rules: use the hazard warning lamps, warning triangle, high visibility vest and so on, as required by law in the country you are driving in.
  3. Switch off: switch off the ignition.
  4. Uncoil the pipe: unwind the pipe stowed under the compressor.
  5. Connect the sealant: connect the pipe from the compressor to the bottle of sealant.
  6. Fit the bottle: turn the sealant bottle over and secure it in the notch on the compressor.
  7. Remove the valve cap: take the cap off the tyre valve and put it somewhere clean.
  8. Connect to the tyre: connect the hose from the sealant bottle to the tyre valve and tighten it firmly.
  9. Check the switch: make sure the compressor switch is at the "O" position.
  10. Uncoil the cable: fully unwind the electric cable stowed under the compressor.
  11. Plug in: connect the compressor's electric plug to the car's 12 V socket.
  12. Fit the sticker: stick the speed limit sticker inside the car.
  13. Switch on: switch on the ignition.
  14. Inflate: turn the compressor switch to the "I" position until the tyre pressure reaches 2.0 bars. Do not disconnect the pipe from the valve while the sealant is being injected, as there is a risk of blowback.
  15. Stop the compressor: put the switch back to the "O" position.
  16. Unplug: disconnect the compressor's plug from the 12 V socket.
  17. Refit the cap: put the cap back on the valve.
  18. Remove the kit: take the kit off the tyre.
  19. Store the bottle: remove the sealant bottle and store it.
  20. Drive to spread the sealant: drive straight away for approximately three miles (five kilometres) at reduced speed, between 12 and 37 mph (20 and 60 km/h), to plug the puncture.
  21. Check the repair: stop, check the repair and measure the tyre pressure using the kit.

Safety points:

  • Do not try to remove any foreign objects stuck in the tyre.
  • Place the speed limit sticker inside the car where the driver can see it.
  • If the pressure has not reached 2 bars after about 7 minutes, the tyre cannot be repaired. Contact a PEUGEOT dealer or a qualified workshop for help.
  • The sealant is harmful if swallowed and irritates the eyes. Keep it out of the reach of children.
  • The use-by date of the sealant is marked on the bottle.
  • Do not put the used bottle in your normal waste. Take it to a PEUGEOT dealer or an authorised waste disposal site.
  • Remember to get a new bottle of sealant from a PEUGEOT dealer or a qualified workshop.
  • Do not drive faster than 50 mph (80 km/h) on a tyre repaired with this kit.

The tyre inflation pressures for your car are shown on the tyre pressure label.

Checking / adjusting tyre pressures

You can also use the compressor on its own, without injecting sealant, to check your tyre pressures and adjust them if needed.

  1. Remove the valve cap: take the cap off the tyre valve and put it somewhere clean.
  2. Uncoil the pipe: unwind the pipe stowed under the compressor.
  3. Connect to the tyre: screw the pipe onto the valve and tighten it firmly.
  4. Check the switch: make sure the compressor switch is at the "O" position.
  5. Uncoil the cable: fully unwind the electric cable stowed under the compressor.
  6. Plug in: connect the compressor's electric plug to the car's 12 V socket.
  7. Switch on: switch on the ignition.
  8. Adjust the pressure: put the switch at position "I" and set the pressure to the value on the car's tyre pressure label. To let air out, press the black button on the compressor pipe, near the valve connection.
  9. Stop the compressor: once the correct pressure is reached, put the switch to the "O" position.
  10. Put the kit away: remove the kit and stow it.
  • If a pressure of 2 bars is not reached after 7 minutes, the tyre cannot be repaired. Contact a PEUGEOT dealer or a qualified workshop for help.
  • Do not drive more than 125 miles (200 km) on a repaired tyre. See a PEUGEOT dealer or a qualified workshop to have the tyre changed.
  • If you adjust the pressure of one or more tyres, you must reinitialise the under-inflation detection system.
  • After a tyre repair, the under-inflation warning lamp stays on until the system is reset.

For more on tyre under-inflation detection, see the corresponding section below.

Access to the tools

If your 208 has a spare wheel, you change a damaged wheel using the tools supplied with the car. The tools are stored in the boot, under the floor.

  1. Open the boot: open the boot lid.
  2. Remove the floor: lift the boot floor and take it out.
  3. Take out the tools: remove the carrier box containing the tools.

List of tools

These are the tools supplied with the car for changing a wheel.

Scroll the table sideways.

No.ToolWhat it is for
1WheelbraceRemoving the wheel trim and the wheel fixing bolts
2Jack with integrated handleRaising the car
3Bolt "cover" toolRemoving the bolt covers on alloy wheels
4Socket for the security boltsAdapting the wheelbrace to the special "security" bolts
5Towing eyeTowing (see the corresponding section below)

Points to remember about the tools:

  • The tools are specific to your car and may vary depending on equipment. Do not use them for anything else.
  • Only use the jack to change a wheel with a damaged or punctured tyre.
  • Do not use any jack other than the one supplied with the car. If your car does not have its original jack, contact a PEUGEOT dealer or a qualified workshop to get the correct one.
  • The jack meets European standards, as defined in the Machinery Directive 2006/42/CE, and needs no maintenance.

If your wheel has a hub cap, refit it by placing its notch facing the valve, then press around its edge with the palm of your hand.

Access to the spare wheel

The spare wheel is stored in the boot, under the floor. Depending on the country, it may be a steel, alloy or "space-saver" wheel.

Peugeot 208 I spare wheel or repair kit stowed under the boot floor

Removing the spare wheel:

  1. Slacken the nut: loosen the central nut.
  2. Remove the fixing: take out the fixing device (nut and bolt).
  3. Lift the wheel: raise the spare wheel towards you from the rear.
  4. Take it out: lift the wheel out of the boot.

Putting the wheel back in place:

  1. Position the wheel: put the wheel back in its housing.
  2. Slacken the nut: undo the nut on the bolt by a few turns.
  3. Fit the fixing: position the fixing device (nut and bolt) in the middle of the wheel.
  4. Tighten: tighten fully until the central nut clicks, so the wheel is held correctly.
  5. Refit the box: put the support box back in the centre of the wheel and clip it in.

If there is no wheel in the well, you cannot put the fixing device (nut and bolt) back in place.

Removing a wheel

Before you start, make the car and its occupants safe.

  • Park where you do not block traffic, on ground that is level, stable and not slippery.
  • Apply the parking brake and switch off the ignition.
  • With a manual gearbox, engage first gear to block the wheels. With an automatic gearbox, put the lever in position P.
  • Check that the parking brake warning lamps on the instrument panel are lit continuously.
  • Ask all occupants to get out and wait somewhere safe.
  • Never go underneath a car raised on a jack. Use an axle stand.

Then follow these steps:

  1. Remove the bolt covers: take the cover off each bolt using tool 3 (depending on equipment).
  2. Slacken the security bolt: fit security socket 4 on wheelbrace 1 and loosen the security bolt (depending on equipment).
  3. Slacken the other bolts: loosen the remaining bolts using wheelbrace 1 only.
  4. Position the jack: place the foot of jack 2 on the ground directly below the front A or rear B jacking point on the underbody, whichever is closest to the wheel you are changing.
  5. Extend the jack: raise jack 2 until its head touches jacking point A or B. The contact area on the car must sit correctly in the central part of the jack head.
  6. Raise the car: lift the car until there is enough space between the wheel and the ground to fit the spare wheel easily.
  7. Remove the bolts: take out the bolts and keep them somewhere clean.
  8. Remove the wheel: take the wheel off.

Make sure the jack is stable on a firm, non-slippery surface, placed only at jacking point A or B, with its head centred on the contact point. Otherwise the car could be damaged, or the jack could collapse or slip and cause injury.

Fitting the wheel

Once the damaged wheel is off, fit the spare wheel as follows.

  1. Fit the wheel: put the wheel in place on the hub.
  2. Start the bolts: screw the bolts in by hand as far as they will go.
  3. Pre-tighten the security bolt: use wheelbrace 1 fitted with security socket 4 (depending on equipment).
  4. Pre-tighten the other bolts: use wheelbrace 1 only.
  5. Lower the car: lower the car fully.
  6. Remove the jack: fold jack 2 and take it away.
  7. Tighten the security bolt: use wheelbrace 1 fitted with security socket 4 (depending on equipment).
  8. Tighten the other bolts: use wheelbrace 1 only.
  9. Refit the covers: put the bolt covers back on each bolt (depending on equipment).
  10. Put the tools away: store the tools in their box.

If your car has alloy wheels and you fit a steel or "space-saver" spare, it is normal for the bolt washers not to touch the spare wheel. The wheel is held by the conical contact of each bolt.

After changing a wheel:

  • To store the punctured wheel in the boot correctly, remove the central cover first.
  • With a "standard" 15-inch spare wheel, do not exceed 50 mph (80 km/h).
  • If your car has 16 or 17-inch wheels, use the "space-saver" spare wheel and do not exceed 50 mph (80 km/h).
  • Visit a PEUGEOT dealer or a qualified workshop as soon as possible to have the bolt tightness and the spare wheel pressure checked.
  • Have the punctured tyre examined. The technician will tell you whether it can be repaired or must be replaced.

Frequently Asked Questions

Where is the puncture repair kit on a Peugeot 208?

The kit is in the under floor storage, under the boot floor. It contains a 12 V compressor with a pressure gauge, a sealant cartridge with a hose and a speed limit sticker.

How fast can I drive after using the Peugeot 208 tyre repair kit?

Do not exceed 50 mph (80 km/h) on a tyre repaired with the kit. Do not drive more than 125 miles (200 km) on it, and see a PEUGEOT dealer or a qualified workshop to have the tyre changed.

What if my 208 tyre will not reach 2 bars with the compressor?

If the pressure has not reached 2 bars after about 7 minutes, the tyre cannot be repaired. Contact a PEUGEOT dealer or a qualified workshop for help.

Why is the tyre warning light still on after fixing a puncture?

After a tyre repair, the warning lamp stays on until the under-inflation detection system is reset. You must reinitialise the system whenever you adjust the pressure of one or more tyres.

Whether your Peugeot 208 has a repair kit or a spare wheel, knowing the steps before you need them makes a roadside puncture far less stressful. Keep to the speed limits afterwards, and have the tyre checked by a PEUGEOT dealer or a qualified workshop as soon as you can.

More Peugeot 208 Guides

If a lamp comes on after a puncture, see our guides to the Peugeot 208 orange warning lights and the Peugeot 208 red warning lights.

Don't forget to follow us on Instagram for more Peugeot guides!

This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.

Related guides: Peugeot 208 model guides.

Cover adapted from a photograph by Harvey Bold — Wikimedia Commons, CC0 (AI edited).

Related guides

Guide ·

Peugeot 208 AdBlue Refilling (2015-present)

BlueHDi Diesel engines on the Peugeot 208 use AdBlue to clean up their exhaust gases. This guide explains what the SCR system does, how far you can drive on a tank of AdBlue, how to store and handle the fluid s…

Guide ·

Peugeot 208 12 V Battery and Jump Starting (2015-present)

A flat 12 V battery is one of the most common reasons a car will not start. This guide explains how to reach the battery on your Peugeot 208, how to start the engine using another battery or a booster, how to c…