Peugeot 208Updated 8 min read

Peugeot 208 I Headlight Bulb Replacement

How to change changing headlamp, indicator, foglamp and rear lamp bulbs on the Peugeot 208 I,. Covers the Peugeot 208 I (2015-present).

Peugeot 208 (2015-present) in a dark workshop with its headlamps on
Image adapted from a photo by Harvey Bold, CC0.

Hello and welcome. In this post, we'll look at which bulbs your headlights and rear lamps use, and how to replace them on the Peugeot 208 I (2015-present). A failed bulb is one of the few faults you can often fix yourself. This guide shows you which bulb each lamp on your Peugeot 208 uses and how to reach and replace it, from the headlamps and foglamps to the rear lamps and number plate lamps. It also covers the lamps that use LEDs, which you should leave to a professional. Some lamps and bulb types depend on the version or equipment fitted, so not every item will apply to your 208.

How do you change a headlight bulb on a Peugeot 208 I?

Open the bonnet, unclip the headlamp cover on the side you need, release the bulb holder and fit a bulb of the same type without touching the glass.

Peugeot 208 I front lamp bulb types, including dipped beam, main beam, sidelamp and direction indicator

Quick Reference

Scroll the table sideways.

SectionIn short
Changing a bulbSafety rules, lens care, LEDs and halogen bulbs
Front lampsFront bulb types and how to replace each one
Rear lampsRear bulb types, boot access and replacement steps

Changing a bulb

Before you change any bulb, read these safety points. Bulbs get very hot, and the headlamp lenses are easy to damage.

  • Ignition and lamps off: only change a bulb with the ignition off and after the lamp has been switched off for several minutes, as there is a risk of serious burns.
  • Do not touch the glass: never touch the bulb directly with your fingers. Use a lint-free cloth.
  • Anti-UV bulbs only: you must use anti-ultraviolet (UV) type bulbs, so you do not damage the headlamp.
  • Same type: always replace a failed bulb with a new one of the same type and specification.
  • LEDs: for light emitting diode (LED) lamps, you must contact a PEUGEOT dealer or a qualified workshop.
  • Halogen bulbs: check that the bulb sits correctly in its housing, so you get good quality lighting.

The headlamps have polycarbonate lenses with a protective coating. To keep the coating and seals in good condition:

  • Do not clean the lenses with a dry or abrasive cloth, or with a detergent or solvent product.
  • Use a sponge and soapy water or a pH neutral product.
  • If you use a high pressure washer on stubborn marks, do not keep the lance pointed at the lamps or their edges for too long.

In some weather, such as low temperatures or humidity, misting on the inside of the headlamp and rear lamp glass is normal. It clears after the lamps have been on for a few minutes.

Front lamps

Your 208 has one of two headlamp designs: model A with a light guide, or model B without a light guide. The front lamps use these bulbs:

Scroll the table sideways.

No.LampBulb
1Main beam headlampsH7-55W
2Dipped beam headlampsH7-55W
3Daytime running lamps/sidelampsLED or W5-5W
4Direction indicatorsPWY-24W
5Front foglamps (with Cornering lighting function, depending on version)H11-55W

Direction indicators: if an indicator lamp flashes more quickly than usual, a bulb on that side has failed.

  1. Remove the holder: turn the bulb holder a quarter turn and pull it out.
  2. Change the bulb: pull out the bulb and replace it.
  3. Refit: reassemble in reverse order.

Amber bulbs, such as the indicators, must be replaced with bulbs of the same colour and specification. When you refit, close the protective cover very carefully so the lamp stays watertight.

Dipped beam headlamps:

  1. Remove the cover: pull on the tab to remove the protective cover.
  2. Disconnect: unplug the bulb connector.
  3. Release the bulb (model A): spread the spring to free the bulb.
  4. Change the bulb: pull the bulb out and fit the new one.
  5. Refit: reverse the steps, with the bulb's positioning lug pointing downwards (model A) or upwards (model B).

Main beam headlamps:

  1. Main connector: remove the main headlamp connector.
  2. Remove the cover: pull on the tab to remove the protective cover.
  3. Disconnect: unplug the bulb connector.
  4. Change the bulb: pull the bulb out and fit the new one.
  5. Refit: reverse the steps, with the bulb's positioning lug pointing downwards.

Daytime running lamps/sidelamps (bulb type):

  1. Remove the holder: turn the bulb holder a quarter turn and pull it out.
  2. Change the bulb: pull out the bulb and replace it.
  3. Refit: reverse the steps.

If your daytime running lamps/sidelamps use LEDs, contact a PEUGEOT dealer or a qualified workshop to replace them.

Foglamps / directional lamps:

  1. Access: reach the front foglamp through the opening below the bumper.
  2. Disconnect: press on the top of the tongue to unplug the bulb holder connector.
  3. Remove the holder: press the two clips (top and bottom) and pull out the bulb holder.
  4. Replace: fit the new module.
  5. Refit: reverse the steps.

You can get the module from a PEUGEOT dealer or a qualified workshop, who can also replace these bulbs for you.

Integrated direction indicator side repeaters:

  1. Insert a screwdriver: slide a flat screwdriver between the door mirror glass and its base.
  2. Lever out the glass: tilt the screwdriver and use it as a lever to remove the glass.
  3. Remove the shell: press the two fixing clips to unclip the door mirror shell.
  4. Remove the repeater: press the central tongue and take out the side repeater.
  5. Change the bulb: pull out the bulb holder and replace the faulty bulb.
  6. Refit: reverse the steps.

A PEUGEOT dealer or a qualified workshop can also replace this bulb for you.

Rear lamps

The rear lamps use these bulbs:

Peugeot 208 I rear lamp bulb types, including direction indicator, reversing lamp and fog lamp

Scroll the table sideways.

No.LampBulb
1Brake lampsLED
2Reversing lampsP21W
3Direction indicatorsPY21W amber
4SidelampsLED
5FoglampP21W

Reversing lamps and direction indicators: you change these two bulbs from inside the boot.

  1. Open the boot: open the boot to reach the side trim.
  2. Remove the grille: take off the access grille from the side trim panel on the relevant side.
  3. Remove the nut: unscrew and remove the nut.
  4. Disconnect: unplug the lamp unit connector.
  5. Remove the lamp unit: unclip it and carefully pull it straight towards you.
  6. Remove the holder: press the four tabs and take out the bulb holder.
  7. Change the bulb: turn the bulb a quarter turn, pull it out and fit a new one.
  8. Refit: reassemble in reverse order.

When refitting, engage the lamp unit in its guides and keep it in line with the car. Tighten the nut enough to seal the lamp, but not so much that you damage it.

Third brake lamp:

  1. Loosen the pins: unscrew the fixing pins on each side of the lamp, without removing them completely.
  2. Unclip: push on the screws to unclip the lamp unit.
  3. Disconnect: unplug the lamp unit connector.
  4. Remove the lamp unit: take it out from the outside.
  5. Remove the holder: turn the bulb holder for the faulty lamp a quarter turn and pull it out.
  6. Change the bulb: pull the bulb out and fit the new one.
  7. Refit: reassemble in reverse order.

Number plate lamps: this is easier with the tailgate half open.

  1. Insert a screwdriver: put a thin screwdriver into the cut-out outside the lens.
  2. Lever: push it outwards.
  3. Remove the lens: take the lens off.
  4. Change the bulb: replace the faulty bulb.
  5. Refit: press the lens to clip it back in.

Foglamp: reach it by passing your hand under the bumper.

  1. Remove the holder: turn the bulb holder a quarter turn and pull it out.
  2. Disconnect: unplug the bulb connector.
  3. Change the bulb: pull the bulb out and fit the new one.
  4. Refit: reverse the steps.

A PEUGEOT dealer or a qualified workshop can also replace these bulbs for you.

Frequently Asked Questions

What bulb does the Peugeot 208 headlamp take?

Both the main beam and dipped beam headlamps take an H7-55W bulb. You must use anti-ultraviolet (UV) type bulbs so you do not damage the headlamp.

Why is my Peugeot 208 indicator flashing fast?

Quicker flashing of the indicator lamp means one of the bulbs on that side has failed. Replace it with an amber bulb of the same colour and specification.

Can I change the LED lamps on my Peugeot 208 myself?

No. Contact a PEUGEOT dealer or a qualified workshop to replace LED lamps, such as the rear brake lamps and sidelamps.

Is condensation inside my Peugeot 208 headlamp normal?

Yes, in some weather, such as low temperatures or humidity, misting inside the headlamps and rear lamps is normal. It clears after the lamps have been on for a few minutes.

Changing a bulb on your Peugeot 208 is straightforward once you know where to reach it. Let the lamp cool, handle the new bulb with a lint-free cloth, and if a job looks tricky or involves LEDs, a PEUGEOT dealer or a qualified workshop can do it for you.

More Peugeot 208 Guides

If a lamp on your dashboard comes on after changing a bulb, see our guides to Peugeot 208 red warning lights, Peugeot 208 orange warning lights and Peugeot 208 green and blue indicator lamps.

Don't forget to follow us on Instagram for more Peugeot guides!

This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.

Related guides: Peugeot 208 model guides.

Cover adapted from a photograph by Harvey Bold — Wikimedia Commons, CC0 (AI edited).

Related guides

Guide ·

Peugeot 208 AdBlue Refilling (2015-present)

BlueHDi Diesel engines on the Peugeot 208 use AdBlue to clean up their exhaust gases. This guide explains what the SCR system does, how far you can drive on a tank of AdBlue, how to store and handle the fluid s…

Guide ·

Peugeot 208 12 V Battery and Jump Starting (2015-present)

A flat 12 V battery is one of the most common reasons a car will not start. This guide explains how to reach the battery on your Peugeot 208, how to start the engine using another battery or a booster, how to c…