Peugeot 108Updated 6 min read

Peugeot 108 I Bulb Replacement

How to change the bulbs on your Peugeot 108: bulb types for the front and rear lamps, step-by-step replacement and when to see a PEUGEOT dealer.

Peugeot 108 (2015-present) in a dark workshop with its headlamps on
Image adapted from a photo by Vauxford, CC BY-SA 4.0.

Hello and welcome. In this post, we'll look at how to change the bulbs on the Peugeot 108 I (2015-present). It also covers the safety points to keep in mind before you start. This guide covers the Peugeot 108 I (2015-present), including vehicles produced from 02/05/2018. The lamps fitted can vary from car to car. For example, position 4 in the rear lamp unit is listed as either a reversing lamp or a foglamp, so check what your own car has.

What headlamp bulb does a Peugeot 108 use?

The dipped beam and main beam headlamps use an HiR2-55W bulb. Use anti-UV type bulbs so the headlamp is not damaged.

Quick Reference

Scroll the table sideways.

SectionIn short
Front lampsFront bulb types, steps and dealer-only lamps
Rear lampsRear lamp unit, number plate and repeater bulbs

Front lamps

The front of your 108 has five types of lamp. You can change the direction indicator and headlamp bulbs yourself. The others are replaced by a PEUGEOT dealer or a qualified workshop.

Peugeot 108 I front lamps: LED sidelamp and daytime running lamp, PY21W indicator, HiR2-55W dipped and main beam, LED foglamp

Scroll the table sideways.

LampBulbReplacement
SidelampsLEDPEUGEOT dealer or qualified workshop
Direction indicatorsPY21W amberYou can do it yourself
Dipped beam / main beam headlampsHiR2-55WYou can do it yourself
Front foglampsNot listed belowPEUGEOT dealer or qualified workshop
Daytime running lampsLEDPEUGEOT dealer or qualified workshop

Before you start:

  • Only change a bulb with the ignition off, and wait until the lamp has been switched off for several minutes. There is a risk of serious burns.
  • Do not touch the bulb with your fingers. Hold it with a lint-free cloth.
  • Use only anti-ultraviolet (UV) type bulbs, so you do not damage the headlamp.
  • Always replace a failed bulb with a new one of the same type and specification.

Caring for the headlamp lenses: the headlamps have polycarbonate lenses with a protective coating.

  • Do not clean them with a dry or abrasive cloth, or with a detergent or solvent.
  • Use a sponge and soapy water, or a pH neutral product.
  • If you use a high pressure washer on stubborn marks, do not point the lance at the lamps or their edges for too long. This protects the coating and the seals.

In some weather, such as low temperatures or humidity, you may see misting on the inside of the headlamp and rear lamp glass. This is normal and clears after the lamps have been on for a few minutes.

Direction indicators (PY21W amber):

  1. Remove the holder: turn the bulb holder a quarter of a turn and pull it out.
  2. Change the bulb: pull the bulb out and fit the new one.

Dipped beam / main beam headlamps (HiR2-55W):

  1. Remove the cover: pull the tab to take off the protective cover.
  2. Release the holder: spread the spring to free the bulb holder.
  3. Replace the bulb: withdraw the bulb holder and bulb, and replace it.
  4. Refit: carry out these steps in reverse order.

For the sidelamps, front foglamps and LED daytime running lamps, contact a PEUGEOT dealer or a qualified workshop. If you have any difficulty with the indicator or headlamp bulbs, they can help too.

Rear lamps

The rear lamp unit holds four bulbs. To change any of them, you remove the whole lamp unit.

Peugeot 108 I rear lamps: P21/5W brake and tail, PY21W indicator, P21W reversing or fog

Scroll the table sideways.

LampBulb
Brake lampsP21/5W
SidelampsP21/5W
Direction indicatorsPY21W
Reversing lamp or foglampP21W
Number plate lampsW5W
Third brake lamp4 W5W bulbs
Direction indicator side repeatersWY5W amber

Rear lamp unit:

  1. Open the boot: lift the tailgate.
  2. Remove the screw: turn the plastic cover and take out the screw.
  3. Move the side trim: push it aside firmly. It is normal for the fitting to bend.
  4. Remove the nut: unscrew it and take it off, making sure it does not fall into the wing.
  5. Take out the lamp unit: pull it hard towards the outside.
  6. Change the bulb: from the back of the lamp unit, pull out the faulty bulb and replace it.
  7. Refit: carry out these steps in reverse order and check the lamp unit is correctly back in place.

Number plate lamps (W5W):

  1. Insert a screwdriver: put a thin screwdriver into one of the cut-outs in the lens.
  2. Unclip the lens: push the screwdriver outwards.
  3. Remove the lens: take it off.
  4. Change the bulb: replace the faulty bulb.
  5. Refit: press on the lens to clip it back in place.

Third brake lamp (4 W5W bulbs):

  1. Unclip the cover: with the boot open, unclip the plastic cover.
  2. Release the lamp unit: press on the metal tabs.
  3. Remove the lamp unit: take it out from the outside of the tailgate.
  4. Remove the bulb holder: squeeze the two plastic tabs.
  5. Change the bulbs: replace the defective bulb or bulbs.
  6. Refit: carry out these steps in reverse order.

Direction indicator side repeaters (WY5W amber):

  1. Release the repeater: push it towards the front or the rear, then pull it towards you.
  2. Replace the bulb holder: disconnect the bulb holder and replace it.

Frequently Asked Questions

What headlamp bulb does a Peugeot 108 use?

The dipped beam and main beam headlamps use an HiR2-55W bulb. You must use anti-UV type bulbs so the headlamp is not damaged.

Can I change the LED sidelamps or daytime running lamps on my 108 myself?

No. contact a PEUGEOT dealer or a qualified workshop to replace the LED sidelamps, the LED daytime running lamps and the front foglamps.

How do I remove the rear light unit on a Peugeot 108?

Open the boot, turn the plastic cover and remove the screw, move the side trim aside, then unscrew the nut and pull the lamp unit hard towards the outside. Take care that the nut does not fall into the wing.

What bulb is in the Peugeot 108 number plate light?

The number plate lamps use W5W bulbs. You unclip the lens with a thin screwdriver in one of its cut-outs, change the bulb, then press the lens back into place.

Always wait for a lamp to cool down before you touch it, and fit a new bulb of the same type and specification. If a step gives you trouble, or the lamp is one needs a professional, a PEUGEOT dealer or a qualified workshop can sort it out for you.

More Peugeot 108 Guides

While you are getting to know your car, see our guides to the Peugeot 108 red warning lights and the Peugeot 108 green and blue indicator lamps.

Don't forget to follow us on Instagram for more Peugeot guides!

This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.

Related guides: Peugeot 108 model guides.

Cover adapted from a photograph by Vauxford — Wikimedia Commons, CC BY-SA 4.0 (AI edited).

Related guides

Guide ·

Peugeot 108 12 V Battery and Jump Starting (2015-present)

A flat battery is one of the most common reasons a car won't start. This guide explains how to reach the 12 V battery on your Peugeot 108, how to start the engine using another battery, and how to charge a disc…

Guide ·

Peugeot 108 Gauges and Service Indicator (2015-present)

The instrument panel on your Peugeot 108 shows you how far the car has travelled and how much fuel is left in the tank. This guide explains how to switch between the total and trip distance displays, how to res…