Peugeot 408 Fuse Box and Fuses (2022-2026)
Hello and welcome. In this article we look at the fuses on the Peugeot 408 I (2022-2026). We will cover who should change a fuse and what to know before adding extra electrical equipment to the car.
How to start, drive and park your Peugeot 408 I, with the parking brake, EAT8, e-DCS6/7, drive selector, driving modes and Stop & Start explained.

Hello and welcome. In this post, we'll look at starting, the gearbox and Stop & Start on the Peugeot 408 I (2022-2026). Knowing how each one works helps you get the best from your car and avoid surprises. It covers the Peugeot 408 I (2022-2026), including vehicles produced from 28/10/2024. Many items depend on the engine, version or equipment fitted, so not everything here will apply to your 408. Many items depend on the engine, version or equipment fitted, so not everything here will apply to your 408.
The engine must be running and the driver's door closed, and you need to press the brake, select a driving mode, then release the brake and press the accelerator. If it still does not release, check that both front doors are properly closed.
Scroll the table sideways.
| Section | In short |
|---|---|
| Driving recommendations | Safe driving advice, key warnings and flooded roads |
| Starting/switching off the engine | How to start and switch off each version |
| Electric parking brake | Applying and releasing the brake, manually or automatically |
| Automatic gearbox (EAT8/e-EAT8) | Push selector modes, paddles and display on EAT8 |
| Electric dual-clutch automatic gearbox (e-DCS6/7) | e-DCS6/7 modes, electric motor and e-functions |
| Drive selector (Electric) | Electric drive selector modes and regenerative braking |
| Driving modes | Normal, Eco, Sport, Electric and Hybrid modes |
| Stop & Start (Petrol) | How STOP mode works and when it won't |
Here is some general advice for driving safely
These are important safety warnings
On flooded roads: strongly advises against driving on flooded roads, because this could seriously damage the internal combustion engine or electric motor, the gearbox and the electrical systems. If you absolutely must drive through a flooded section:
If you are in any doubt about the state of your car, contact a PEUGEOT dealer or a qualified workshop.
Noise (Electric): electric versions are very quiet when driving, so you need to pay particular attention and always check the area around the car when manoeuvring. At speeds of up to 19 mph (30 km/h), the pedestrian horn warns other road users that the car is there. The cooling fan comes on during charging to cool the on-board charger and the traction battery, and inside the car you may hear certain perfectly normal noises specific to electric vehicles.
The electronic key must be inside the passenger compartment, and it is also detected in the boot. If the key is not detected, a message appears: move the key so the engine can be started or switched off. If there is still a problem, follow the Key not detected – Back-up starting or Back-up switch-off steps below.

Starting:
If one of the starting conditions is not met, a message appears. In some cases, a message tells you to turn the steering wheel while pressing the "START/STOP" button to help unlock the steering column.
Starting rechargeable hybrid vehicles:
Wait for the READY lamp before leaving Park mode. The system starts in Electric mode by default and decides whether to start the petrol engine depending on parameters such as battery charge level or outside temperature. You can change the driving mode at any time with the mode selector. In Electric mode the car makes no noise when it starts, so watch out for pedestrians and cyclists who may not hear it coming, even with the pedestrian horn.
Switching off:
The automatic gearbox locks in mode P, and in some cases you need to turn the steering wheel to lock the steering column. If the car is not immobilised, the engine will not stop. With the engine off, the braking and steering assistance are also cut off, so there is a risk of losing control of the car. Never leave the car with the electronic key still inside.
Starting electric vehicles: the drive selector must be in mode P.
In automatic mode, the electric parking brake applies itself when you switch off the engine and releases when you move off. Automatic mode is on by default, and it can be deactivated in certain situations. At any time with the engine running:
You must apply the electric parking brake whenever the car is stationary.
Indicator lamp: the lamp comes on both on the instrument panel and on the control, with the message "Parking brake applied". It goes off when the brake is released, with the message "Parking brake released". The lamp flashes when you make a manual request to apply or release the brake.
These are the safety points
Manual release (ignition on or engine running):
If you do not press the brake pedal, the parking brake stays on and a message appears. Manual application: with the car stationary, briefly pull the control. The control lamp flashes to confirm the request.
Automatic release: make sure the engine is running and the driver's door is closed. The brake releases gradually as you move off:
If the brake does not release automatically, check that the front doors are properly closed. When stationary with the engine running, do not press the accelerator unnecessarily, as the parking brake could release.
Automatic application: with the car stationary, the brake applies automatically when you switch off the engine. It does not apply automatically if the engine stalls or goes into STOP mode with Stop & Start. In automatic mode, you can still apply or release the brake manually at any time with the control. To hold the car still with the engine running, briefly pull the control.
On petrol versions, the EAT8 is an automatic 8-speed gearbox with a push selector, plus a manual mode using paddles behind the steering wheel. On rechargeable hybrids, the e-EAT8 has a push selector and a regenerative braking function, and works the same as other EAT8 gearboxes apart from the manual mode and regenerative braking.
Scroll the table sideways.
| Mode | What it does |
|---|---|
| P | Auto Park: press the button to park. The front wheels are blocked. |
| R | Reverse |
| N | Neutral: to free-wheel and move the car with the ignition off |
| D | Automatic mode: the gearbox changes gear based on driving style, road profile and load |
| M | Manual mode (Petrol): press the button, then change gear with the steering-mounted controls |
| B | Automatic mode with regenerative braking (Rechargeable hybrid): the gearbox also brakes when you release the accelerator |
Using the selector:
To switch quickly between D and R without going through N: in R, push backwards past the point of resistance for D; in D, push forwards past the point of resistance for R. To return to N, push without passing the point of resistance.
Paddles (depending on equipment): in mode M or D, pull the "+" or "-" paddle towards you and release to shift up or down a gear. You cannot use them to select neutral or to engage or leave reverse.
Scroll the table sideways.
| Display | Meaning |
|---|---|
| P | Parking |
| R | Reverse |
| N | Neutral |
| D1.8 | Automatic forward gear |
| B1.8 | Automatic forward gear with regenerative braking activated |
| M1.8 | Manual forward gear |
In all-electric driving, the gear engaged is not shown. The gearbox status stays on the instrument panel for a few seconds after you switch off the ignition.
Operation: only appropriate mode changes are accepted. If you need to press the brake pedal to change mode, a message appears on the instrument panel. Keep these warnings in mind:
Automatic mode: the gearbox picks the best gear based on ambient temperature, road profile, load and driving style. For maximum acceleration, press the accelerator fully down (kick-down): the gearbox changes down or holds the gear until maximum engine speed. The paddles let you pick a gear temporarily if vehicle and engine speed allow. Manual mode: the gearbox only changes gear if vehicle and engine speed allow.
Regenerative braking (Rechargeable hybrid): this function imitates engine braking, so the car slows more quickly when you release the accelerator, without pressing the brake pedal. The energy recovered partly recharges the traction battery, but this does not show on the charge level indicator. This slowing down does not switch on the brake lamps.
The e-DCS6 (hybrid) and e-DCS7 (rechargeable hybrid) are 6-speed and 7-speed electrified dual-clutch automatic gearboxes with a push selector and a manual mode using paddles behind the steering wheel. They include an electric motor that improves the petrol engine's performance, reduces fuel consumption and allows all-electric driving.
Scroll the table sideways.
| Mode | What it does |
|---|---|
| P | Auto Park: press the button to park. The front wheels are blocked. |
| R | Reverse |
| N | Neutral: to free-wheel and move the car with the ignition off |
| D | Automatic mode: the gearbox changes gear based on driving style, road profile and load |
| M | Manual mode (Hybrid): press the button, then change gear with the steering-mounted controls |
| B | Automatic mode with regenerative braking (Rechargeable hybrid): the gearbox also brakes when you release the accelerator |
The selector works exactly as on the EAT8: from N, with your foot on the brake, push forwards for R or backwards for D without passing the point of resistance, then let go. Push past the point of resistance to switch directly between D and R, and push without passing it to return to N. In mode M or D, the "+" and "-" paddles (depending on equipment) shift up or down a gear, but cannot select neutral or reverse.
Scroll the table sideways.
| Display | Meaning |
|---|---|
| P | Parking |
| R | Reverse |
| N | Neutral |
| D | Automatic forward gear |
| M1.6 | Manual forward gear (Hybrid) |
| B | Automatic forward gear with regenerative braking (Rechargeable hybrid) |
The gear engaged is shown in Manual and Sport modes, but not in all-electric driving. The gearbox status stays displayed for a few seconds after you switch off the ignition.
Electric motor (Hybrid): the motor in the gearbox is used for the first start, supplies 12 V power through the DC/DC converter and assists the petrol engine. It can:
It does this through the automatic functions e-Boost, e-Creeping, e-Launch, e-Queueing and e-Parking. A manual mode, e-Auto, lets you activate or deactivate the petrol engine restarting while driving. In mode P or N, the engine compartment can get louder as the traction battery starts charging: this is normal and not a fault.
Operation: the same rules and warnings apply as on the EAT8. Only appropriate mode changes are accepted, the car moves off in R, D or M once the brakes are released, and you must never press the accelerator and brake together. Opening the driver's door in mode N engages mode P with an audible signal, and below 3 mph (5 km/h) it engages mode P with a risk of sudden braking. If the battery fails, chock one of the wheels with the chock(s) from the tool kit.
Hybrid automatic functions: these work only if the traction battery is charged enough, and none of the five can be deactivated.
Repeated use of the brake pedal restarts the petrol engine to provide braking assistance. On rechargeable hybrid versions, automatic and manual modes behave as on the EAT8: the gearbox picks the best gear, kick-down gives maximum acceleration, and gear changes only happen if vehicle and engine speed allow.
On electric versions, the drive selector is a pulse selector with a regenerative braking function. It controls traction based on driving style, road profile and load, and with regenerative braking on it also manages engine braking when you release the accelerator.
Scroll the table sideways.
| Mode | What it does |
|---|---|
| P | Park: the front wheels are locked and the button lights up |
| R | Reverse: engage it with your foot on the brake pedal |
| N | Neutral: to move the car with the ignition off and let it free-wheel |
| D | Drive (automatic forward gear) |
| B | Brake: regenerative braking, the button lights up when active |
With the ignition on, the instrument panel shows P, R, N, D or B to match the selector.
To switch quickly between D and R, push past the point of resistance: backwards from R for D, forwards from D for R. Push without passing it to return to N. The Brake function imitates engine braking, so the car slows more quickly when you release the accelerator, without pressing the brake pedal.
The modes available depend on your engine and equipment. To choose one:
The selected mode works straight away and stays shown on the instrument panel once the message disappears (except Normal mode). On electric versions, you cannot select a mode until the READY lamp is displayed.
Petrol and hybrid versions start in Normal mode each time you switch on the ignition.
On some petrol versions, in mode D with Eco or Normal selected, gradually and fully releasing the accelerator lets the car free-wheel (Coasting mode) to save fuel. The engine speed drops to idle and the engine gets quieter: this is normal.
Rechargeable hybrid versions start in Electric mode each time you switch on the ignition.
If Electric mode cannot start or stay on, the message "Electric mode currently unavailable" appears and the car changes to Hybrid mode. After several months without use, the petrol engine may restart even with a charged battery. After several engine starts without the engine warming up properly, Electric mode may be temporarily unavailable because fuel dilutes in the oil, and "Electric mode unavailable: automatic operation in progress" appears. Drive approximately 50 miles (80 km) in motorway conditions or approximately 125 miles (200 km) in town to get it back. This causes no mechanical or electrical damage and can happen several times in the car's life.
Electric versions start in Normal mode each time you switch on the ignition.
Stop & Start puts the engine into standby (STOP mode) when the car is stationary, for example at red lights or in traffic jams, and restarts it (START mode) as soon as you show you want to move off. It is designed mainly for town driving to cut fuel use, emissions and noise, and it does not affect the car's functions, in particular the braking.

Deactivation and reactivation: the function is on by default when you switch on the ignition. You change it in the ADAS touch screen application or through the Shortcuts for driving aids, and a message on the instrument panel confirms the change. If you switch it off while the engine is in STOP mode, the engine restarts immediately. One indicator lamp shows the engine is in STOP mode, and another shows the function is deactivated or faulty.
Deactivate Stop & Start before working under the bonnet, so the engine cannot restart and injure you. It is also strongly recommended that you switch it off before driving into a flooded area (see Driving recommendations).
Main conditions for operation:
STOP mode: the engine goes into standby when you press the brake pedal until the car stops in mode D or with the M button pressed, or when the car is stationary in mode N. A time counter adds up the time spent in standby during the journey and resets each time you switch on the ignition.
The engine will not go into standby if the conditions above are not met, or on a steep slope (up or down), with Sport mode selected (depending on equipment), when needed to keep the cabin comfortable, or when demisting is on. In these cases the indicator lamp flashes for a few seconds, then goes off.
Avoid it where you can. If you absolutely must, the water must be no deeper than 15 cm, Stop & Start should be off, and you should drive as slowly as possible without stalling, never above 6 mph (10 km/h), without stopping or switching off the engine.
The engine must be running and the driver's door closed, and you need to press the brake, select a driving mode, then release the brake and press the accelerator. If it still does not release, check that both front doors are properly closed.
The engine will not go into standby if a condition is not met, such as the driver's seat belt unfastened or an outside temperature outside 0°C to 35°C. It also stays on on a steep slope, in Sport mode, when demisting or when needed to keep the cabin comfortable.
Electric mode needs enough battery charge and an outside temperature between approximately -5°C and 45°C. After several short engine starts it can also be temporarily unavailable, and driving approximately 50 miles (80 km) on the motorway or approximately 125 miles (200 km) in town brings it back.
Knowing how your 408 starts, parks and changes gear makes everyday driving easier and safer. Keep this guide handy. If in doubt, ask a PEUGEOT dealer or a qualified workshop.
If a lamp comes on while you are driving, see our guides to the Peugeot 408 red warning lights, the Peugeot 408 orange warning lights and the Peugeot 408 green and blue indicator lamps.
Don't forget to follow us on Instagram for more Peugeot guides!
This is an independent guide, not an official Peugeot publication. If in doubt, contact a PEUGEOT dealer or a qualified workshop before carrying out any work.
Related guides: Peugeot 408 model guides.
Cover adapted from a photograph by Alexander-93 — Wikimedia Commons, CC BY-SA 4.0 (AI edited).
Hello and welcome. In this article we look at the fuses on the Peugeot 408 I (2022-2026). We will cover who should change a fuse and what to know before adding extra electrical equipment to the car.
Hello and welcome. In this article we look at the tyre under-inflation detection system on the Peugeot 408 I (2022-2026): how it works, what to do when the alert comes on, how to reinitialise it and w
Hello and welcome. In this post we cover the lights on the Peugeot 408 I (2022-2026). We'll look at caring for the headlamp lenses, which LED lamps need a professional, the front and rear lamp layouts